Noritz NRC111OD Installation Manual Download

Page: 37 / 37

Changing Other Features

Adjusting the Temperature / Water Quantity Display

Note: The setting must be done within the first 10 minutes of connecting electrical power to the water heater.

Table of Setting Items

Display

Power On/Off Button

ENTER Buttton

Setting Procedure

1. Turn the water heater off by pressing the Power On/Off Button on the remote controller.

2. Disconnect, then reconnect electrical power to the water heater.

3. Press the MENU Button inside the cover, select "Initial settings" using the ▲/▼ Buttons.

4. Press the ENTER button, the "Initial settings" screen appears on the display.

5. Select "[

°F / gal] <

----> [°C

/ L]" using the ▲/▼ Buttons.

6. Press the ENTER Button and select either [

°F / gal] or [

°C

/ L] using the ▲/▼ Buttons.

7. Press the ENTER Button, "Set complete Please wait..." appears on the display for 5seconds and

then the "Initial settings" screen appears on the display.

8. To confirm the setting, turn the water heater on by pressing the Power On/Off Button on the remote

controller.

Remote Controller

▲/▼ Buttons

MENU Button

Item

Choices (factory defaults shaded)

Celsius / Liter

Fahrenheit / Gallon

display mode.

°F / gal

(Fahrenheit / Gallon)

°C / L

(Celsius / Liter)

Summary of Contents for NRC111OD






































Search results

Summary of Contents for NRC111OD

Reviews:

Related manuals for NRC111OD

Brands by name

Popular brands

Noritz NRC111OD, Installation Manual

Search results

Summary of Contents for NRC111OD

Reviews:

Related manuals for NRC111OD

Brands by name

Popular brands