background image

18

11.

 

Plumbing Applications

Recirculation System

Combination Potable Water and Space Heating System

Cold Water Supply

Isolation
Kit(*4)

Gas Supply

Aquastat(*3)

Pump Control Signal(*2)

Relay for Pump
(if larger than 85 Watts)

Hot Water

Optional 8-10 Gallon
Storage Tank
(To alleviate cold water sandwich)

Globe
Valve

Pump(*1)

Expansion Tank
(Install according
to local code)

Fixtures

Hot Water Return

R

B

W

Pump

120VAC

105

Neutral
Ground

Live

S

Isolation
Kit(*1)

Gas Supply

Backflow Preventer
(optional)

Check
Valve(*3)

Cold Water
Supply

Mixing Valve(*5)

Hot Water

Pump(*2)

Flow Switch(*4)

Fixtures

Air Handler

Notes:

Notes:

Use Honeywell Aquastat 

(Model L6006A or L6006C)

Aquastat Wiring

1. Noritz recommends the use of an Isolation Kit with
    the installation.
    These kits include an integrated shut-off and serv-
    ice valve with unions and a pressure relief valve.

2. Size the pump to provide a maximum of 3 GPM 
    with a head pressure equal to the loss through the 
    water heater and Air Handler.
3. Check valve required if it is not included with the
    pump.

4. Set the flow switch to deactivate the Air Handler
    when the domestic hot water flow reaches 3 GPM.
    Adjust as necessary to prevent cycling.  

5. If the system requires water for space heating at
    a higher temperature than for other uses, means
    such a mixing valve shall be provided to temper
    the water for the other uses to help prevent scald
    -ing.

6. Expansion tank required if a backflow preventer is
    installed.

1. Size the pump to provide a maximum of 2 GPM 
    through the system at 10 ft of head plus piping
    losses. 
    Adjust the flow using a globe valve and verify the 
    flow rate with the maintenance monitors.

2. Pump Control Signal is the preferred method
    to control the recirculation pump.  
    For pumps larger than 85W, a relay connection must 
    be used. If the Pump Control Signal is not used, 
    an Aquastat may be used to control the pump.
    

3. Use an Aquastat if the water heater is not control-
    ling the pump. 
    Set the Aquastat to 10

°

F below the set output 

    temperature. 
4. Noritz recommends the use of an Isolation Kit
    with the installation.
    These kits include an integrated shut-off and serv-
    ice valve with unions and a pressure relief valve. 

Optional
Expansion Tank(*6)

NORITZ

Tankless Gas

Water Heater

NORITZ

Tankless Gas

Water Heater

Summary of Contents for N-0751M-DV





























Reviews: