background image

18

10.

 

Plumbing Applications

(See notes for Sizing)

Recirculation System

Pump

Fixtures

Cold Water Supply

Check

Valve

Hot Water Return

Check Valve

Pressure

Relief

Valve

Hot Water

Shutoff Valve

Drain

R

B

W

Use Honeywell Aquastat 

(Model L6006A or L6006C)

Pump

AC120

Aquastat Wiring

105

Neutral

Ground

Live

5

Heating System

Cold Water Supply

Check

Valve

Hot Water Return

 Pressure

Relief Valve 

Hot Water

Shutoff Valve

Drain

Air Scoop 
(Optional)

Temp. &

Press. Gauge 

(Optional)

Hydronic Heat 

Exchanger or 

Radiant Heat 

Piping

Pressure

Reducing

Valve

(Optional)

Shutoff

Valve

Backflow

Preventer

(Optional)

Boiler Drain Valve

Heating 
Controls

Mixing Valve

Cold Water Supply

Tempered Potable Hot Water

Hot Water for Heating

If the system requires water
for space heating at a higher
temperature than for other 
uses, means such as a mixing
valve shall be provided to
temper the water for the other
uses to help prevent scalding.

For Space Heating Purposes:

Check Valve

Aquastat

Aquastat

Pump

Expansion Tank

(Install According

to Local Codes)

Optional 8-10 Gal.
Storage Tank
(To Alleviate Cold
Water Sandwich)

(Install According

  to Local Codes)

(See notes for Sizing)

Expansion

Tank

For Baseboard
Applications:
Please contact
Noritz for 
compatibility.

*   Size the pump to provide at least 1.58 GPM through the system at 10 Ft of Head plus 
    piping losses. Check the maintenance monitors on the unit to make sure the pump 
    is providing that much flow.
** Adjust the flow using a gate valve and verify the flow rate with the maintenance monitors.

*   Size the pump to provide at least 1.58 GPM through the system at 10 Ft of Head plus 
    piping losses. Check the maintenance monitors on the unit to make sure the pump 
    is providing that much flow.
** Adjust the flow using a gate valve and verify the flow rate with the maintenance monitors.

NORITZ

Gas Water

Heater

NORITZ

Gas Water

Heater

Gas 

Water

Heater

 SAR8584C̲015̲025̲E̲J.p65

06.11.13, 10:19 PM

Page 18

Adobe PageMaker 6.5J/PPC

Summary of Contents for N-0631S




























Reviews: