background image

22

Periodic Maintenance

If the water drain valve (with water filter) is covered with debris, the hot water may not run 

smoothly, or the unit may put out cold water. Check and clean the filter as explained below.

*  To avoid burns, wait until the equipment cools down before draining the water.     

The appliance will remain hot after it is turned off.

Water Drain Valve (with Water Filter)

1. Close the water supply valve.

2. Open all hot water fixtures.

3. With a bucket ready, remove the inlet and outlet 

drain plugs (about 0.4 gallon (1.4L) will drain out)

4. Take the water drain valve (with water filter) out of 

the inlet. (See illustration to right).

5. Clean the water drain valve (with water filter) with 

a brush under running water.

6. Replace the water drain valve (with water filter) 

and close the drain plugs.

  (Take care not to lose the packing.)

7. Close all hot water fixtures.

8. Open the water supply valve and check that 

    water does not leak from the drain plugs or water 

drain valve (with water filter).

Water Supply 

Valve

Inlet

Packing

Water drain valve 

(with water filter)

Regular Maintenance-2

(Ex. NRC98DV (GQ-C2857WS-FF US))

Summary of Contents for EcoTough NRC98-DV-LP

































Reviews: