background image

6

EP2 Pump System

© 2021 Nordson Corporation

1072608-04

Safety Labels

Table 1 contains the part number and description for each safety label on this equipment. 

Safety labels are provided to help you operate and maintain your equipment safely.
See Figure 1 for the location of safety labels.

Table 1    Safety Labels

Item

Part

Label

Description

1

- - - - - -

WARNING:

 Disconnect main power supply before removing this panel.

2

- - - - - -

WARNING: 

Read instruction manual and observe all warnings.

WARNING: 

High pressure device eye protection required.

WARNING: 

INJECTION HAZARD

Airless spray painting equipment can cause serious injury if the spray 

penetrates the skin. Do not point the gun at anyone or any part of the 

body. In case of penetration, adequate medical aid must be immediately 

obtained.

WARNING: 

COMPONENT RUPTURE

To avoid rupture or injury do not operate this pump at a pressure higher 

than the maximum working pressure.

WARNING: 

FIRE

Static voltage is developed by airless spraying. The pump, associated 

system, and object being sprayed must be grounded to prevent static 

discharge sparks which could start a fire.

3

242867

WARNING:

 Risk of electrical shock

4

- - - - - -

WARNING: 

Rotating shafts. Do not operate without shroud.

5

- - - - - -

WARNING: 

HOT SURFACE

Operation of the pump causes surface to get hot.  To avoid personnel 

injury, do not touch surface during or after operation.

Summary of Contents for EP2









































Reviews: