background image

ValveMate 7100 Controller

13

www.nordsonefd.com   [email protected]

   +1-401-431-7000    Sales and service of Nordson EFD dispensing systems are available worldwide.

Indicator Lamps

The indicator lamp 

 at the upper left corner above the LED display will 

illuminate whenever the dispense valve is actuated.

The center front panel has five indicator lamps used to indicate the 
operational mode.

MODE

RUN

CYCLE

SETUP

STEADY

TEACH

PURGE

CYCLE

Maximum Air Pressure Caution 
Caution symbol informing that the maximum air input pressure is 7.0 bar (100 psi). Excessive 
air input pressure may damage the equipment.  

Foot Pedal / Finger Switch Connector 
Switch symbol identifies the connector for a momentary contact closure switch for dispense 
initiates. An optional foot pedal, P/N 7014865 may be ordered. 

Power Input Current 
Input current symbol specifying that DC current is utilized on the power supply connector. 
The current is derived from an external 24 VDC source. 

Chassis Connection  
This symbol identifies the chassis connection terminal. Used for grounding the chassis to 
shunt leakage current and / or to enhance system ESD protection.

Back Panel Markings

Operating Features (continued)

Summary of Contents for ValveMate 7100





























Reviews: