background image

26

   Locate the Reed Switch (52) and the Magnet (51) 

on the left side of the Pulley (50). Turn the Pulley 

until the Magnet is aligned with the Reed Switch. 

Make sure that the gap between the Magnet 

and the Reed Switch is about 1/8 in. (3 mm). If 

necessary, loosen the #8 x 3/4" Tek Screw (13), 

move the Reed Switch slightly, and then retighten 

the Screw. Reattach the Motor Hood (not shown) 

with the five #8 x 3/4" Hood Screws (not shown) 

and run the treadmill for a few minutes to check for 

a correct speed reading.

SYMPTOM: The incline of the treadmill does not 

change correctly

a.     Hold down the Stop button and the Speed increase 

button, insert the key into the console, and then 

release the Stop button and the Speed increase 

button. Press the Stop button and then press the 

Incline increase or decrease button. The tread-

mill will automatically rise to the maximum incline 

level and then return to the minimum level. This will 

recalibrate the incline system. If the incline does not 

begin calibrating, press the Stop button again, and 

then press the Incline increase or decrease button 

again. When the incline is calibrated, remove the 

key from the console.

SYMPTOM: The walking belt slows when walked on

a.  

  If an extension cord is needed, use only a 3-con-

ductor, 14-gauge (1 mm

2

) cord that is no longer 

than 5 ft. (1.5 m).

b.   If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may 

become damaged. Remove the key and UNPLUG 

THE POWER CORD. Using the hex key, turn both 

idler roller screws counterclockwise, 1/4 of a turn. 

When the walking belt is properly tightened, you 

should be able to lift each edge of the walking belt 

2 to 3 in. (5 to 7 cm) off the walking platform. Be 

careful to keep the walking belt centered. Then, 

plug in the power cord, insert the key, and run the 

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

c.   Your treadmill features a walking belt coated with 

high-performance lubricant. IMPORTANT: Never 

apply silicone spray or other substances to 

the walking belt or the walking platform unless 

instructed to do so by an authorized service 

representative. Such substances may deterio-

rate the walking belt and cause excessive wear. 

If you suspect that the walking belt needs more 

lubricant, see the front cover of this manual.

d.   If the walking belt still slows when walked on, see 

the front cover of this manual.

Idler Roller Screws

5–7 cm

b

Top

View

52

3 mm

13

51

50

Summary of Contents for NETL17812.0





































Reviews: