NordicTrack Grt320 Manual Download Page 3

1.

Read all instructions in this manual before
using the weight bench. 

2.

The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.

3.

It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.

4.

Use the weight bench only as described in
this manual. 

5.

Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.

6.

Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately. 

7.

Keep children under the age of 12 and pets
away from the weight bench at all times.

8.

Always keep an equal amount of weight on
each end of your barbell (not included) when
you are using it. When adding or removing
weights, always keep some weight on both
ends of the barbell to prevent the barbell
from tipping.

9.

Do not use a barbell that is longer than six
feet with the weight bench.

10. When you are using the leg lever, place a

barbell with the same amount of weight on
the weight rests to balance the bench.

11.  Keep hands and feet away from moving parts.

12.  Always wear athletic shoes for foot protec-

tion while exercising.

13. The weight bench does not include weights.

The weight bench is designed to support a
maximum of 460 pounds, including the user,
a weight bar, and weights. Do not place more
that 210 pounds, including a weight bar and
weights, on the weight rests. Do not place
more than 130 pounds on the leg lever.

14. Make sure that the adjustment knobs are

inserted completely and tightened into the
uprights before beginning any exercise.

15. When adjusting the position of the backrest,

make sure that the adjustment pin is inserted
through both adjustment tubes and that the
pin clip is attached (see page 10).

16. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-
ing down.

17. Always remove the curl post from the front

leg before performing leg curls with the leg
lever.

18. Always exercise with a partner. When you

are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.

19. When you put weight on the weight rests,

make sure you put at least ten pounds on the
leg lever to balance the weight bench.

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. 

3

Important Precautions

WARNING: 

To reduce the risk of serious injury, read the following important precautions

before using the weight bench.

Summary of Contents for Grt320

















Reviews: