background image

18

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to 

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do 

not do this, you may damage the console displays 

or other electrical components.

Plug in the power cord 

(see page 16). Next, locate 

the power switch on the 

treadmill frame near the 

power cord. Press the 

power switch into the reset 

position.

IMPORTANT: The console features a display demo 

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as 

you plug in the power cord and press the power 

switch into the reset position, the demo mode is 

turned on. To turn off the demo mode, hold down 

the Stop button for a few seconds. If the displays 

remain lit, see THE SETTINGS MODE on page 22 to 

turn off the demo mode.

Next, stand on the 

foot rails of the 

treadmill. Find the 

clip attached to the 

key, and slide the clip 

onto the waistband of 

your clothes. Then, 

insert the key into 

the console. After a 

moment, the displays 

will light. IMPORTANT: In an emergency, the key can 

be pulled from the console, causing the walking 

belt to slow to a stop. Test the clip by carefully tak-

ing a few steps backward; if the key is not pulled 

from the console, adjust the position of the clip.

IMPORTANT: Before you use the treadmill, take the 

following steps to ensure that the console shows 

the correct incline level of the treadmill: First, 

press the Incline increase button once. Next, press 

either the Incline decrease button or the lowest 

numbered incline button to set the treadmill to its 

lowest setting. When the frame stops moving, the 

treadmill is ready for use.

HOW TO USE THE MANUAL MODE

1.  Insert the key into the console. 

   See HOW TO TURN ON THE POWER at the left.

2.   Select the manual mode.

   Press the Manual button on the console to select 

the manual mode.

3.  Start the walking belt. 

   To start the walking belt, press the Start button, the 

Speed increase button, or one of the Speed but-

tons numbered 2 through 20.

   If you press the Start button or the Speed increase 

button, the walking belt will begin to move at 2 

Km/H. As you exercise, change the speed of the 

walking belt as desired by pressing the Speed 

increase and decrease buttons. Each time you 

press one of the buttons, the speed setting will 

change by 0.1 Km/H; if you hold down the button, 

the speed setting will change in increments of 0.5 

Km/H. Note: After you press the button, it may take 

a moment for the walking belt to reach the selected 

speed setting.

   If you press one of the numbered Speed buttons, 

the walking belt will gradually change speed until it 

reaches the selected speed setting.

   To stop the walking belt, press the Stop button. The 

time will begin to flash in the display. To restart the 

walking belt, press the Start button or the Speed 

increase button.

4.  Change the incline of the treadmill as desired.

   To change the incline of the treadmill, press the 

Incline increase or decrease button or one of the 

Incline buttons numbered 0 through 10. Each time 

you press one of the buttons, the treadmill will 

gradually adjust to the selected incline setting.

Reset

ETNE99815

Key

Clip

Summary of Contents for C 220i





































Reviews: