Nordic Bella Owner'S Manual Download Page 5

Page: 5 / 40

Your Hot Tub is designed to provide optimum performance when
connected to the maximum electrical service. The listing below will show
the various options and performance levels available on your hot tub.

A new GFCI must be used for your Hot Tub installation. Do not use
an existing breaker (GFCI), as its condition is unknown.

AMERICAS

60Hz 120v/240v 120v/240v 240v

Circuit Breaker 20A/50A 15A/50A 50A
Number of Wires 3/4 3/4 4

EUROPE

50Hz 230v 230v

Circuit Breaker 16A 32A
Number of Wires 3 3

On all systems, your Hot Tub must be connected to a dedicated
circuit breaker that is not shared with any other equipment.

DO NOT USE EXTENSION CORDS OF ANY KIND.

Clean tub of all debris.

Use a garden hose to fill your hot tub through the empty filter
canister (to avoid air pockets during filling) to the appropriate
level of a minimum 2 inches (5.08cm) over the filter skimmer.

DO NOT USE WATER THROUGH A WATER SOFTENER.

Locate the shut-off T-valves. Make sure they are in the up or
open position. (See page 8)

Check heater and pump unions. Occasionally during
shipping these become loosened. A simple tightening of
these (if necessary) will do, being careful not to over tighten.
(See page 8)

Once water has reached correct level, turn power on to the
hot tub.

To activate jets and to purge air from the pump, press/push jet
button located on the top side control. A second press/push

will put the pump on high speed. Repeat this process until
water flows from the jets. When the jets are working, set the
pump to low speed. (See page 25)

Some start-up chemicals will be needed; please see your
dealer for recommendations.

Set the temperature located on the top side control (See page
24) to the desired setting. The heater will shut off when the
water temperature reaches the set temperature.

10. Place the hot tub cover on tub. Keeping the cover on the

hot tub when the tub is not in use will help minimize
operating costs.

11. The time it will take for the water temperature to reach the

desired setting will vary.

Whirlpool Diverter Jet(s):

Your hot tub is equipped with at least one Whirlpool Diverter jet (2,
3, or 4 position), located on filter wall. These jets when turned will
divert water to different groups of jets. Each position is reached
with a 90 degree turn of the whirlpool jet face. Always turn the
collar of the diverter jet clockwise when possible. Remember,
turning your diverter will affect the flow of water to different seat
jets. Adjust to suit your personal needs.

Topside Control Pad:

Your hot tub is equipped with an electronic topside control pad. The
topside control pad wil allow you to control the speed of the pump,
the light, and the temperature setting, as well as some programming
options. Familiarize yourself with the topside control by viewing the
Operation Guide at the back of this manual.

Permanently connected installation instructions

Electrical installation should be performed by a qualified licensed electrician.
1. Remove cabinet service panel. The panel is secured with pan

head Phillips screws.

2. Remove system controller cover.
3. If spa was manufactured with a cord.

a. Disconnect cord wires from terminal TB1 and

ground wire from ground bar.

b. Loosen cord strain relief.
c. Remove cord.
d. Remove stain relief.

4. Drill hole for conduit through bottom or side of spa.

5. Secure conduit at system controller box.
6. Connect hot and neutral wires to corresponding terminals TB1.

Connect ground wire to grounding bar on the outside of box by
running it though hole marked for ground wire.

7. Voltage selection for North American 60 Hz systems.

a. 120V installation. Attach jumper to J11 and J32. A