manualshive.com logo in svg

Nordic ID RF601, User Manual

Share
Download
Nordic ID RF601 User Manual Download Page 34

© 2006 Nordic ID Oy
RF601 User Manual 

 

May 2006  

Version 1

28

���������������

APPENDIX B - Introduction to the Laser Engine     

A laser diode produces a single beam of coherent light which deflects off a mirror, and is emitted from the laser engine 
used inside the RF651. The total deflection of the single beam is 53° (standard version), and the scan frequency is 39 
scans per second.
 
When the laser beam strikes a barcode, the dark bars absorb most of the light while the light spaces reflect most of it. 
Thus, changes in the reflected light can be used to deduce the barcode into electronic format. A photo diode is used to 
sense the reflected laser light and generate a current proportional to the reflected light signal. The current then produces 
an analogue voltage, which is further amplified, filtered to minimise noise related problems and then finally sent to a 
digitiser, which transforms the analogue signal into digital form representing the barcode. This is called the Digitised Bar 
Pattern (DBP). 
 
The DBP data is then sent to the decoder board for processing into a host-compatible format and further applications 
are based on the software used. 
The technical specifications of the laser engine used in the RF651 are listed in the table below.

Table:

 Laser engine technical specifications

Item

Description

Laser Power (at 650 nm)

Scan mode;  1.7 mW (± 0.2 mW) 
Aim mode:    0.5 mW (± 0.05 mW) 
CDRH Class II/IEC Class 2

Optical Resolution

0.004 in. minimum element width

Print Contrast

Minimum 25% absolute dark/light reflectance measured at 650 
nm.

Scan Angle

Wide:    47° ± 3°
Narrow: 35° ± 3°

Environmental characteristics
Ambient light immunity:

Sunlight:        107,640 lux (10,000 ft. candles)
Artificial Light 4,844 lux (450 ft. candles) 

Scan rate

92 minimum., 104 typical, 116 max. scans/sec (bidirectional)

Scanning angles

scan angle: 47° ± 3° (wide), 35° ± 3° (narrow)
skew: 100% UPC at 5 in. ± 50° from normal
pitch: 100% UPC at 5 in. ± 65° from normal
tilt: 100% UPC at 5 in. ± 35° from vertical

Reading distances

Near  ranges  on  lower  densities  (not  specified)  are  largely 
dependent upon the width of the bar code and the scan angle.

  

Summary of Contents for RF601














































Reviews:

No comments

Brands by name

Popular brands

Load more brands