background image

2 Year Limited Warranty

What Does Our Warranty Cover?

- Any defect in material or workmanship

For How Long After the Original Purchase?

- 2 Years

What Will NorCross Do?

- At our option repair or replace.

How Do I Obtain Service?

- Securely pack the unit, and mail prepaid via insured post

to:    NorCross  Marine  Products,  Inc.,  Wa rr a n t y
Department, 1629 Prime Court - Suite 800,Orlando, FL
32809.  A copy of the original sales receipt is required as
the proof of purchase for warranty repairs.  Please be
sure to include your name, address, email address, and
a daytime phone number within the package.

What Does Our Warranty Not Cover?

- Batteries
- Damage from misuse, neglect, or acts of nature (light-

ning, floods, power surges, etc.

- Products purchased outside the USA and Canada
- Products serviced by the owner or a service facility not

expressly authorized by NorCross Marine Products

- Products purchased more than 24 months from the cur-

rent date.

How Does State Law Relate to this Warranty?

-  This warranty gives you specific rights.  You may also

have other rights which vary from state to state.

20

To Set the Units:

1.  Turn on the Display

2.  Press and hold the "up" and "down" keys at the same

time for 2 seconds.

3. To set the units to feet press the “up” key.  “FT” will

flash on the Display.

4. To set the units to meters press the “down” key. “M”

will flash on the Display.

5. The display will return to the normal mode automati-

cally after five seconds.

Shallow Alar m

The shallow alarm function can be set for depths ranging
from 3 to 200 feet and triggers an alarm when the depth is
less than the setting.  

To set the SHALLOW ALARM (upper alarm):

1. Press and hold the "UP"

key for 2 seconds (Figure
14).  The current alarm set-
ting will be displayed on
the display. "000" is the
default setting.  The alarm
will be reset to "000" if the
power to the unit is turned
off.

Figure 14

17

Summary of Contents for ML100DR






















Reviews: