background image

 

 
 
 

1

1

 

Introduction 

Congratulations on your purchase of the NORAC UC5 Spray Height Control System.  This 
system is manufactured with top quality components and is engineered using the latest 
technology to provide operating reliability unmatched for years to come. 

When properly used the system can provide protection from sprayer boom damage, improve 
sprayer efficiency, and ensure chemicals are applied correctly. 

Please take the time to read this manual completely before attempting to install the system.  A 
thorough understanding of this manual will ensure that you receive the maximum benefit from 
the system. 

Your input can help make us better!  If you find issues or have suggestions regarding the parts 
list or the installation procedure, please don’t hesitate to contact us. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Every effort has been made to ensure the accuracy of the information contained in 
this manual.  All parts supplied are selected to specially fit the sprayer to facilitate 

a complete installation.  However, NORAC cannot guarantee all parts fit as 
intended due to the variations of the sprayer by the manufacturer. 

Please read this manual in its entirety before attempting installation. 

Summary of Contents for UC5 Active Roll Control



























Reviews: