NOMACORC NomaSense CO2 P2000 User Manual Download Page 3

Page: 3 / 12

Specifications - NOMASense CO

P2000

General

• Min. 2000 measurements on fully charged

battery

•  Sample flow 130 - 165 ml/min standard
•  Auto power-off after 1 minute
•  Memory function for 10 measurements
•  Display hold function (also after power

off)

• Charging time for NiMH-battery: 3 hours

(auto off)

• Operational temperature: 0 - 40°C
• Humidity: <95% RH (non-condensing)

Sensor

•

Non-dispersive infrared (NDIR),

temperature compensated

•  Range: 0 – 2.5 g/L
•  Resolution: 0.01 g/L
• Accuracy:
•  50 mg/L abs. @ 0 – 1 g/L
•  100 mg/L abs. @ 1 – 2.5 g/L
•  Expected life-time > 3 years

Measuring system

•  Measuring time: 10 sec.
•  Sample volume: approx. 23 mL
•  Built-in pump max. -200 mbar vacuum,

expected life-time > 500 hours (180.000

measurements)

• Calibration: 0% CO

and 100% CO

gas

Cabinet

•  Weight: 0.5 kg
•  Size: 74 x 63 x 135 mm (W x H x D)
•  Class: IP53
•  Material: Anodized aluminium

Summary of Contents for NomaSense CO2 P2000













Search results

Summary of Contents for NomaSense CO2 P2000

Reviews:

Related manuals for NomaSense CO2 P2000

Brands by name

Popular brands

NOMACORC NomaSense CO2 P2000, User Manual

Search results

Summary of Contents for NomaSense CO2 P2000

Reviews:

Related manuals for NomaSense CO2 P2000

Brands by name

Popular brands