NOMA 052-6962-0 Owner'S Manual Download Page 10

10

Here are some suggestions to help you maintain your fan.

1.   Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade 

attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.)

2.   Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid 

scratching the finish. The plating is sealed with a lacquer to minimize discolouration or tarnishing. Do not use water when cleaning.

This could damage the motor, the wood, or possibly cause an electric shock.

3.   You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced beauty. Cover small 

scratches with a light application of shoe polish.

4.   There is no need to oil your fan. The motor has permanently lubricated sealed ball bearings.

PROBLEM

Fan will not start

Fan sounds noisy

Lights shut off and 

will not come back on.

SOLUTION

Check main and branch circuit fuses or breakers.

Check line wire connections to the fan and switch wire connections in the switch housing. 

Make sure all motor housing screws are snug.

Make sure the screws that attach the fan blade bracket to the motor hub are tight.

Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing.

Allow a 24-hour "breaking-in" period. Most noises associated with a new fan disappear during this time.

If using ceiling fan light kit, make sure the screws securing the glassware are tight. Check that the light bulb is 

also secure.

Make sure there is a short distance from the ceiling to the canopy. It should not touch the ceiling.

Make sure your ceiling box is secure and rubber isolator pads are used between mounting bracket and outlet 

box.

This unit is equipped with a wattage limiting device. Lamping in excess of 190 W will disable your ceiling 

fan's light kit. To reset your light kit you must turn the power off and install bulbs of lower wattage,, keeping 

the wattage under 190 W. Restore power to your ceiling fan and continue normal operation. 

Warning: Make sure the power is off at the electrical panel box before you attempt any repairs. Refer to the section, 

This Noma® product carries a limited ten (10) year warranty against defects in the motor, and a one (1) year warranty 

against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge 

within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not 

guaranteed against wear or breakage due to misuse and/or abuse.

"making electrical connections".

!

Care of Your Fan

Troubleshooting

Warranty

Summary of Contents for 052-6962-0





















Reviews: