Nokia 1506 Service Manual Download Page 91

Page: 91 / 140

RH-128

Baseband Description and Troubleshooting

COMPANY CONFIDENTIAL

Page 5-

Issue 1

Table of Contents

Key components overview................................................................................................................ page 5-5
System block diagram....................................................................................................................... page 5-6
Platform Introduction......................................................................................................................... page 5-6

Display and Keypad......................................................................................................................... page 5-12
Troubleshooting............................................................................................................................... page 5-13
Power Does Not Stay ON................................................................................................................. page 5-13

Power Does Not Stay ON Troubleshooting........................................................................... page 5-14

Audio Faults ..................................................................................................................................... page 5-15

No Sound in Earpiece & Microphone (refer to Audio PA Circuit design)........................... page 5-15
Audio Faults Troubleshooting ............................................................................................... page 5-16
Audio PA Circuitry................................................................................................................... page 5-18

Display Faults................................................................................................................................... page 5-18

Display Faults Troubleshooting............................................................................................. page 5-18

Keypad Faults .................................................................................................................................. page 5-20

Keypad Faults Troubleshooting............................................................................................. page 5-20

Vibrator Faults (reference to the Vibrator Circuit Design) ........................................................... page 5-21

No Vibration Troubleshooting................................................................................................ page 5-21
Vibrator Circuit ........................................................................................................................ page 5-22

USB Interface Faults........................................................................................................................ page 5-23

USB Interface Disabled Troubleshooting.............................................................................. page 5-23
USB Circuitry........................................................................................................................... page 5-24

UIM Card Unreadable troubleshooting .......................................................................................... page 5-24
Charging Faults Troubleshooting................................................................................................... page 5-25

Summary of Contents for 1506







































































































Search results

Summary of Contents for 1506

Reviews:

Related manuals for 1506

Brands by name

Popular brands

Nokia 1506, Service Manual

Search results

Summary of Contents for 1506

Reviews:

Related manuals for 1506

Brands by name

Popular brands