background image

Active data pins

Configurable per customer requirement

Optical Specifications
Fiber optic budget (point to
point)
Fiber optic budget (ring)
    3 unit ring
    4 unit ring
Peak power wavelength
Fiber optic connectors

12 dB (typical)

10 dB (typical)

8 dB (typical)

820 nanometers

two ST style

Power requirements

90 to 250 VAC at 50 to 60 Hz

Power supply type

External

Dimensions

1.75" x 19" (1U)

Warranty

Three years

SAFETY

SAFETY

Note: READ THIS FIRST

1.

 

Do not look into any fiber optic connection or fiber optic cable.

2.

 

Do not connect GEMINI EXPRESS MULTIPLEXER to any type of public
network.

3.

 

Do not connect any outdoor cabling to the GEMINI EXPRESS
MULTIPLEXER without proper lightning protection.

4.

 

Do not use unauthorized power supplies or cables.

5.

 

Do not connect to non-5250 protocol devices.

6.

 

Do not disassemble or modify the power supply and its cables.

7.

 

Disconnect all cables prior to configuration.

8.

 

Devices attached to the UTP network must comply with the voltage and
current limits for Class 2 Power-Limited Signal Circuits as defined by article
725 of the National Electrical Code and Section 16 of the Canadian Electrical
Code.

9.

 

For your safety, receptacles must be properly wired and grounded.

10.

 

Never attempt to service equipment connected to the data cable network or
the grounded receptacle during an electrical storm.  Exposure to lethal
voltages may occur when lightning is present.

The following FCC statement applies to the NLynx GEMINI EXPRESS
MULTIPLEXER.

Federal Communications Commission (FCC) Statement
Note:

  This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.  These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.  This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.  Operation of this equipment in a residential area is likely to
cause harmful interference, in which the user will be required to correct the
interference at his own expense.  Unauthorized changes or modifications could
void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.  Operation is subject to the
following two conditions:  (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Summary of Contents for Gemini Express













Reviews: