manualshive.com logo in svg

NLT AS14006, Manual

Share
Download
NLT AS14006 Manual Download Page 16

17 

A. Device Configuration 

1. General Setup Tab

Wireless network is enabled:

 Disable/Enable the Wireless network by 

clicking the button 

Operating Frequency Buttons

:  

(Mode) the drop box selection shows the WiFi mode that will be used for 
this SSID.  The choice is Legacy (802.11b and g) or N (802.11n) 

(Channel) the drop box selection shows the available channels for 
selection, this depends on the country selected.  

(Width) the drop box selection shows two bandwidths for selection 
20MHz and 40MHz 

Note: To apply changes click Save & Apply or for many changes click 
Save and after finishing click save & Apply (at the bottom of the screen) 

2. Advance Settings Tab

Select the advanced settings tab

Country  Code: 

The drop box selection shows the available country 

codes (ISO/IEC Alpha2). This Selection affect the Operating Frequency 
and the Transmit power 

Note: To apply changes click Save & Apply or for many changes click 
Save and after finishing click save & Apply (at the bottom of the screen) 

Summary of Contents for AS14006























Reviews:

No comments

Brands by name

Popular brands

Load more brands