Type plates NivuLog Easy V3
Note:
This symbol indicates that the NivuLog Easy V3 is equipped with an integrated SIM chip.
Note:
These operating instructions are part of the device and must be available for the user at all
times. The safety instructions included therein must be observed.
WARNING:
It is strictly prohibited to disable the safety equipment or modify its mode of operation.
2.5 Installation of spare and wear parts
Be advised that spare and accessory parts that have not been supplied by the manufacturer have also not
been inspected or approved by the manufacturer. The installation and/or use of such products can possibly
have a negative impact on the specified constructional properties of the device. The manufacturer shall not be
liable for any damages that arise from the use of non-original parts and non-original accessory parts.
2.6 Storage of the product
To safeguard the NivuLog Easy V3 , ensure that all relevant data was transferred to the Device to Web
server. If necessary, initiate a transmission directly on the device via the solenoid switch (see "Solenoid
switch" on page 73) and then check again that all of the relevant data has been transferred. This particularly
applies to the "Interval" connection type. If the "Interval & wakeup" connection type has been selected, you
can also initiate the transmission via the Device to Web server (see "Basic settings" on page 99). With the
"Online" connection type, the determined measurement data is immediately transferred to the Device to Web
server. The data on the server is always up-to-date and the device can be switched off at any time.
2.6.1 Separate storage of the device and power supply unit (recommended)
Remove the power supply unit before disconnecting the cables and antenna. If possible, switch off the supply
or charging voltage before disconnecting the cables from the V IN and GND clamps (see "Connecting the
sensors, actuators and power supply" on page 54). Store the NivuLog Easy V3 and power supply unit in the
original packaging.
The configuration and most recently determined data are retained. The system time also continues to run
thanks to the hardware real-time clock equipped with its own buffer battery. This means that a valid time basis
is available immediately following recommissioning (see "Technical details about the system time" on page
67).
12 of 141
NivuLog Easy V3 - Rev. 03 as of 24.10.2018
Summary of Contents for NivuLog Easy V3
