Nittoh UP-45SV Series Operation And Maintenance Manual Download Page 7

 

UP-45SVG-7

 with MVS-4 4-way 3-position directional control manual valve. 

Advance/Hold/Retract. 

 
1

 

Plug in the pump. 

2

 

Shift manual valve handle to left side position (stop at 45

°

) and depress “ON” switch 

to advance the cylinder (flow to port “A” , port “B” returns flow to the reservoir). 
 
Before  retracting  the  cylinder,  return  valve  handle  to  neutral  (front)  position  (both 
ports “A” and “B” are blocked). 

3

 

Shift  valve  handle  to  right  side  position  and  depress  “ON”  switch  to  retract  the 
cylinder (flow to port “B”, port “A” returns flow to the reservoir). 

 
 

5

 

Maintenance 

5-1 Hydraulic working oil 
 

 

Kind of oil 

 

Use only Nittoh NHO-32 hydraulic oil or an approved, high-grade oil (ISO #32, viscosity : 
32 cSt @40

°

C) with these pumps to promote long pump life. 

 

 

Oil temperature 

 

Aptitude  temperature  for  use  of  hydraulic  oil  is  max.  55

°

C.  In  case  it  happens 

unacceptable  rise  in  oil  temperature,  stop  working  so  as  to  decrease  oil  temperature  or 
take such a measure as installation of an oil cooler. 

 

  Oil exchange    

CAUTION 

 

The frequency of oil change will depend upon general working conditions, severity of use 
and overall cleanliness. 300 hours (working time) of use or about 3 months is considered 
as a standard change interval. Periodically compare samples oh the reservoir oil with new 
oil and inspects oil color for contaminants or differences. 

 

Remove  oil  feeding  plug  and  tilt  the  pump  to  drain  out  old  oil.  Be  careful  that  such 
impurities  as  dusts do  not  enter  info  the  reservoir  and  new  oil  is  filled  up  to  the  gauge 
level mark shown on pump. Precautions when oil changed are; 
 

 

Retract all cylinders fully to the return position. 

 

Do not fill with even a small quantity of replenishment of different kinds of oil. 

 

Be careful that impurities or foreign matter do not enter info new oil. 

 

 

  Others 

      WARNING 

 

When  oil  enters  into  a  eye,  wash  it  away  fully  with  clean  water  and  consult  a  doctor 
immediately.  In  case  oil  enters  into  the  skin  of  such  a  wound,  wash  it  away  with  soapy 
water and consult a doctor without delay. 

 

Summary of Contents for UP-45SV Series


















Reviews: