background image

4

INSTRUCTIONS FOR

THIS TOOL

About Your Tool

WARNING

 Use of power is limited to the power source 

specified by the rating plate.

 Operate under the power source the voltage 

fluctuating rate of which is within ±10 % of the 

rated voltage, and the frequency of which is 

50/60Hz of sinusoidal wave.

 Before using the tool, make sure the power 

source to which it will be connected is fitted 

with an earth leakage breaker to prevent electric 

shock.

 Extension cord should be selected after ensuring 

the diameter is compatible with the length of the 

extension.

Beware of extremely long power cord (particularly 

wound up thin cords) as they may cause drops in 

voltage which weaken the magnetism, adversely 

affecting the performance and function of the unit. 

Do not share the extension cord with any other 

electric machine tools.

Extension Cord

Max. Length

Nominal cross-sectional area

10 m

1.25 mm

2

 or more

15 m

2.00 mm

2

 or more

30 m

3.50 mm

2

 or more

 When performing maintenance, inspection, 

replacement or adjustment of parts, make sure 

to disconnect the attachment plug from the 

receptacle.

 To replace the Indexable Insert after using, do 

not touch with bare hands as the Indexable 

Insert and holder are heated at high temperature.

 Protect your body from cutting chips.

The heated chips can be spread out when cutting. 

Wear the safety goggle, working gloves, and long 

sleeve working cloths and safety shoes to protect 

your body. Also keep away your face.

 Use our original Indexable Inserts.

 Do not use the worn or damaged Indexable 

Insert.

 The service life of Indexable Insert can be 

shortened depending on the surface finishing 

conditions of the stainless plate.

(e.g. : The life of Indexable Insert for No.2B finishing 

material is about half of the BA finishing material.)

 For machining the thin plate, if non-chamfered 

portion is below than 1.5 mm, the plate can be 

placed between the Indexable Insert and the 

guide sleeve, thereby the chamfering amount 

can be greatly varied. Adjust the chamfering 

amount so that the non-chamfered portion can 

be surely larger than 1.5 mm. 

(Fig.1)

Ma

x

. chamfering level for

mild steel

Chamfering
Level

chamfering

Fig.1

 Size of material which can be chamfered.

The value minimum hole diameter and minimum radius are 
obtainable when the O.D. 22 guide sleeve is replaced with 
the accessory Ball Bearing 687ZZ.

Fig.2

1. USAGE

This tool is for chamfering workpieces with a 

Indexable Insert.

2. CHECK THE CONTENTS OF THE PACKAGE

Check the contents and make sure that the tool 

does not have any damage which may have 

occurred during transportation. The contents should 

correspond to the list as follows. In case of damage/

missing parts, please contact the sales agent from 

whom you purchased the tool.

Package Contents

Qty check

CIRCUIT BEVELER  ECB-0203

1set

Sub-handle

1

Grip guard

1

Indexable Insert with hole 12.7

1

Indexable Insert Set Screw 4 x 7

1

Hex. Socket Screw Key 5

1

Spanner T-15D

1

Spanner 8 x 10

1

Ball Bearing 687ZZ

1

Gauge C3

1

Instruction Manual

1

Declaration of Conformity

1

Caution for Use

1

Summary of Contents for ECB-0203













Reviews: