ninjakitchen.com
ninjakitchen.com
CARE & MAINTENANCE
ORDERING REPLACEMENT PARTS
CLEANING
Separate all parts. Wash all containers in warm, soapy water with a soft cloth.
• Hand-Washing
Wash processor bowl, nesting workbowl, lid, spindle, discs, and blade assemblies in warm, soapy water.
When washing the blade and disc assemblies, use a dishwashing utensil with a handle to avoid direct
hand contact with blades.
Handle blade and disc assemblies with care to avoid contact with sharp edges. Rinse and air-dry thoroughly.
• Dishwasher
All attachments are dishwasher safe. Ensure the blade or disc assemblies are is removed from the bowl
before placing in the dishwasher. Exercise care when handling blade or disc assemblies.
• Motor Base
Turn off the unit and unplug the motor base before cleaning. Wipe motor base with a clean, damp cloth.
DO NOT
use abrasive cloths, pads, or brushes to clean the base.
STORING
Wrap the power cord around the cord wrap on the back of the motor base. Store the unit upright and
store all blade assemblies inside or attached to their respective containers with their lids locked in place.
DO NOT
stack items on top of the containers. Store any remaining attachments alongside the unit or in a
cabinet where they will not be damaged or create a hazard.
RESETTING THE MOTOR THERMOSTAT
This unit features a unique safety system that prevents damage to the motor and drive system should you
inadvertently overload the unit. If the unit is overloaded, the motor will be temporarily disabled. Should this
occur, follow the reset procedure below.
1
Unplug the unit from the electrical outlet.
2
Allow the unit to cool for approximately 15 minutes.
3
Remove the container’s lid and blade assembly. Empty the container and ensure no ingredients are
jamming the blade assembly.
IMPORTANT:
Ensure that maximum capacities are not exceeded. This is the most typical cause of
appliance overload.
If your unit needs servicing, please call Customer Service at 1-877-646-5288. So we may better assist you,
please register your product online at
registeryourninja.com
and have the product on hand when you call.
To order additional parts and attachments, visit
ninjaaccessories.com
.
6
When finished, press the button on the lid near the handle to unlock, then turn
counterclockwise and lift up from the bowl. Always remove the small chopping
blade assembly before emptying ingredients from the workbowl by carefully
grasping it by the top of the shaft and lifting it out of the bowl. Then, remove
the disc spindle.
7
Remove workbowl by grasping the textured center and lifting up. Remove bowl
from base by turning it counterclockwise, then lifting it up.
8
Press the Power button to turn the unit off, then unplug the unit. Refer to the
Care & Maintenance section for cleaning and storage instructions.
USING THE NESTING WORKBOWL
(not included with all models)
1
Place Precision Processor
®
Bowl on base and turn
clockwise to lock in place.
2
Place the nesting workbowl in the processor bowl with
the arrow on the workbowl aligned with the arrow on
the processor bowl handle.
3
Place the disc spindle through the opening in the
middle and sit it on the drive gear. Then, place the small
chopping blade over the spindle inside the workbowl.
4
Place ingredients in the workbowl, then place the feed chute lid on
the bowl and turn clockwise until you hear a click, indicating the lid is
locked in place. Press the Power button to turn unit on.
5a
If using the Auto-iQ
®
Program
PUREE
, the preset feature will
automatically stop at the end of the program. To stop the unit at any
time, press
PUREE
.
5b
If using a manual program, once the ingredients have reached your
desired consistency, press the active button again, or wait for the unit
to come to a complete stop after 60 seconds.
NOTES:
• Do not make dough in the workbowl.
• Large food pusher must be inserted in the feed chute for the unit to run.
• Use only the PUREE program or the manual programs when using the nesting workbowl.
IMPORTANT:
If the control panel is flashing, this means the lid, bowl, or food pushers are not locked
in place correctly. Review steps to ensure you are installing all components correctly.
