background image

LIABILITY EXCLUSION

Since robbe Modellsport is not in a position to monitor the handling of these batteries, we expressly deny all liability and guarantee 
claims where the batteries have been incorrectly charged, discharged or handled.

Safety Notes regarding LiPo batteries:

•  Do not place the battery in water or any other liquid.
•  Never heat or incinerate the pack, or place it in a microwave oven.
•  Avoid short-circuits, and never charge the battery with reversed polarity 
•  Do not subject the battery to pressure or shock loads, and never distort or throw the pack
•  Never solder directly to the battery 
•  Do not modify or open the battery 
•  Batteries must only be charged with a suitable charger; never connect the battery directly to a mains power supply.
•  Never charge or discharge a battery in bright sunlight, or close to a heater or open fire. 
•  Do not use the battery in areas subject to high levels of static electricity. 
•  Any of these errors can result in damage to the battery, explosion or fire. 
•  Keep the battery out of the reach of children
•  If electrolyte should escape, do not expose it to fire, as the material is highly inflammable and may ignite.
•  Do not allow fluid electrolyte to come into contact with eyes. If this should happen, flush with copious amounts of water and 

contact a doctor without delay.

•  The fluid electrolyte can also be removed from clothing and other objects by rinsing with copious amounts of water.

11

Operating Instructions - SOLO PRO 290 RTF 2.4 GHz No. NE2516

Summary of Contents for SOLO PRO 290





















Reviews: