background image

 

 

Usermanual  

NIMOS Micro-Trac

 

Page 

7

 

2 Safety 

instructions 

2.1 Safety 

first: 

 

WARNING! 

Hazards or unsafe use which COULD result in death or severe personal injury. 

CAUTION! 

Hazards or unsafe use which COULD result in minor personal injury or damage to the machine. 

IMPORTANT!

  Indicates that equipment or property damage could result if instructions are not followed. 

NOTE!

   

Gives helpful information. 

 

2.2 Safe 

operation 

 

 

 

¾

Persons younger than 18 years, are not allowed to use the machine (according to country regulations). 

¾

Maintenance and cleaning is only permitted, when the engine is not running. 

 

¾

When leaving the cabin, one always needs to turn off the engine, engage the parking brake and take the keys 

from the ignition lock. 

¾

Before coupling implements, one has to consult the coupling and operation instructions. 

¾

Take care that there are no people in the direct neighbourhood of the machine when tipping the platform and 

steering with the carrier. 

¾

The maximal allowed transverse slope during operation of the machine is 15 degrees in both directions. 

¾

The driver needs to be well-informed about the operating and maintenance instructions of the machine. 

¾

Transport of passengers and animals in th

e tipping platform is prohibited. 

 

 

2.3 Safe 

Maintenance 

¾

  For the user of the machine it is only allowed to do daily maintenance. All the other services have to be don 

by an authorised NIMOS dealer. 

¾

  Service and maintenance is only save when the engine is not running and the parking brake is on. When 

maintaining the driving system the front and back tyres have to be blocked to prevent the machine from 
rolling. 

¾

  Spare parts must have the same specifications as delivered by NIMOS. 

¾

  In the engine compartment are several dangerous parts. Such as the, the radiator, the exhaust pipe. The 

Fan of the cooling can run without notice. This can cause serious injury.  

 

¾

  For maintenance it best to wait until the machine parts are could down. 

¾

  Never use bare hands to close or prevent hoses from leaking. The 

pressure of the hydraulic system can cause serious injury. 

¾

  Repairs on battery are not allowed. Keep away from fire or smoking. 

¾

  Only let the machine running when the area has good ventilation. 

¾

  Always use the red safety pin with maintenance under the tipping box.  

 

IMPORTANT!

 The responsibility for changes, respectively modifications of the machine is 

not for the producer, but for the one who has carried them out. 

)

  

WARNING!

 One 

always

 needs to set the red safety leg during inspection, maintenance or repair under 

the tipped platform to protect the platform against coming down. 

Summary of Contents for Micro-Trac




























Reviews: