manualshive.com logo in svg

NimbeLink Skywire NL-SWDK, User Manual

Share
Download
NimbeLink Skywire NL-SWDK User Manual Download Page 24

 

For all other responses, review network status responses online in your

 

 

 

 

 

 

 

 

 

 

 

respective AT Commands Manual. 

 

2.16.2.

LTE Modem Network Registration 

To check network registration for these modems: 

-

NL-SW-LTE-TSVG 

-

NL-SW-LTE-TNAG 

-

NL-SW-LTE-TEUG 

-

NL-SW-LTE-TC4EU 

-

NL-SW-LTE-TC4NAG 

follow this procedure:  
 
In the terminal program, type the command: 

AT+CEREG?

 

followed by the Enter key, and the terminal should respond with: 

+CEREG: 0,1

​

 or 

​

+CEREG: 0,5

 

For all other responses, review network status responses online in your

 

 

 

 

 

 

 

 

 

 

 

respective AT Commands Manual. 
 

2.16.2.1.

NL-SW-LTE-GELS3 

 

To test NL-SW-LTE-GELS3, follow this procedure: 
 
If you recently updated the firmware on your NL-SW-LTE-GELS3, verify that

 

 

 

 

 

 

 

 

 

 

 

cellular functionality is enabled. To do so, type the following command into the

 

   

 

 

 

 

 

 

 

 

 

 

terminal program: 

AT+CFUN=1 

followed by the Enter key, and the terminal should respond with: 

OK

 

Next, in the terminal program, type the command: 

AT+CEREG? 

For Firmware 4.3.2.0 or newer, the terminal should respond with: 

+CEREG: 0,1 

​

or

​

 +CEREG: 0,5 

For all other responses, review network status responses online in your

 

 

 

 

 

 

 

 

 

 

 

respective AT Commands Manual. 
 

 

 

PN 30005 rev 23

© NimbeLink Corp. 2019. All rights reserved.

24

 

Summary of Contents for Skywire NL-SWDK



























Reviews:

No comments

Brands by name

Popular brands

Load more brands