background image

 

1. Introduction 

1.1 Orderable Part Numbers 

 

Orderable Device 

Description 

Carrier 

Network 

Type 

NL-SWDK 

Skywire Development Kit 

Any 

Any 

NL-SW-LTE-S7618RD 

LTE CAT1, Verizon 

Verizon 

LTE 

NL-SW-LTE-S7648 

LTE CAT1, AT&T/T-Mobile 

AT&T, T-Mobile, etc. 

LTE 

NL-SW-LTE-S7588-V

 

LTE CAT4, Verizon 

Verizon 

LTE 

NL-SW-LTE-S7588-V-B

 

LTE CAT4, Verizon 

Verizon 

LTE 

NL-SW-UAV-S7588 

LTE CAT4, Verizon 

Verizon 

LTE 

NL-SW-LTE-S7588-T 

LTE CAT4, AT&T/T-Mobile, HSPA 

AT&T, T-Mobile, etc. 

LTE 

NL-SW-LTE-S7588-T-C 

LTE CAT4, AT&T/T-Mobile, HSPA 

AT&T, T-Mobile, etc. 

LTE 

NL-SIM-ATT

 

3FF SIM for AT&T 

AT&T 

GSM/LTE 

NL-SIM-TMO 

3FF SIM for T-Mobile 

T-Mobile 

GSM/LTE 

NL-SIM-VOD 

3FF SIM for Vodafone 

Vodafone 

GSM/LTE 

NL-SIM-COM 

3FF SIM for Verizon 

Verizon 

LTE 

TG.30.8113 

Taoglas Antenna 

 

Any 

CAB.011 

Taoglas SMA to UFL cable 

 

 

 

1.2 Product Overview 

This documents details interfacing with the 4G LTE CAT 1 & CAT 4 NL-SW-LTE-S7xxx 
family of Skywire® modems for Verizon or AT&T on the Skywire Development Kit.  

The Skywire Development Kit includes one baseboard, antenna, power supply, SIM 
cards, and debug cables. Skywire modems must be purchased separately. The kit 
enables you to develop your application directly on the Skywire modem with three 
different ways to connect: 

● Connect your PC to the Skywire modem UART port via onboard USB-to-UART 

converter and send AT commands directly to the modem through PC terminal 
applications. You can also connect over USB for access to multiple COM ports. 

● The kit is an Arduino shield, so you can plug the kit directly onto an Arduino 

microcontroller. Please see Section 3: Common Next Steps for links to example 
documentation. 

● To connect the kit to a different processor or development kit, a 14-pin header 

breaks out the necessary signals for easy connection to any device. The modem 
supports I/O levels from 1.65-5.5V, simplifying connection to other systems. 

 

PN 30229 rev 9

© NimbeLink Corp. 2018. All rights reserved.

3

 

Summary of Contents for NL-SW-LTE-S7588




















Reviews: