Nilfisk-Advance SW 5070 B Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 35

background image

S31NUK5080(2)2001-01

7

PREPARING A NEW MACHINE

(battery version)

At the end of the recharge operation close all

the caps of the batteries, clean their upper part

and remove all possible acid remains.

Connect the batterys connector to the machine.

3-

If the machine is supplied with no battery,

they have to be procured and mounted.

It is recommended to use the service of quali-

fied personnel to choose and to install the new

battery.
The electric connection cables that are supplied

together with the machine can be used for the

battery connection.

Warning: Before starting the recharge op-

eration, the connector of the battery must

be disconnected from the machine.

Place the brush as per the figure and make

sure that the fixing profiles match perfectly with

the relevant holes. Coupling may be helped

thanks to a light pressure of your hand.
Now the machine is ready to be used.

«
...
7
8
9
10
11
...
»

Summary of Contents for SW 5070 B




































Reviews:

No comments

Related manuals for SW 5070 B

Brand: Janome Pages: 84

Brand: Pfaff Pages: 19

Brand: Castex Pages: 9

Citymaster 2000

Brand: HAKO Pages: 186

Brand: Jack Pages: 58

Brand: Pacific Pages: 8

memory craft 4900

Brand: Janome Pages: 89

Brand: Kärcher Pages: 15

Minoltafax 1600e

Brand: Konica Minolta Pages: 127

Brand: Fimap Pages: 44

Brand: GE Pages: 18

Brand: GE Pages: 20

Brand: GE Pages: 2

15638680 (REV. 1 E/S) 29878

Brand: GE Pages: 2

Brand: GE Pages: 2

2 2-9992 2-9992

Brand: GE Pages: 32

Brand: GE Pages: 48

Brand: GE Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands