Nilfisk-Advance SW 5070 B Operating Instructions Manual Download Page 29

Page: 29 / 35

S31NUK5080(2)2001-01

CONTROL

EVERY

20 h

EVERY

50 h

EVERY

100 h

UP ON

DELIVERY

Warning: these operations must be carried out with the machine off.

All periodic or extraordinary maintenance operations must be performed by skilled per-

sonnel, or by an authorised service centre.

For any maintenance work on the engine, refer to its instruction manual.

SUMMARY TABLE

(petrol-operated version maintenance)

TWICE

WEEK

Engine filter cleaning
Panel filter cleaning
Engine oil level check

FIRST TIME

OR WITHIN

ONE MONTH

Belt tightening
Filter shaker
Nut and screw tightening
Side and central brush

condition
Filters, gasket seal, flaps

Control devices cable

adjustment

Engine oil

replacement

OR WITHIN

EIGHT MONTHS

Summary of Contents for SW 5070 B




































Search results

Summary of Contents for SW 5070 B

Reviews:

Related manuals for SW 5070 B

Brands by name

Popular brands

Nilfisk-Advance SW 5070 B, Operating Instructions Manual

Search results

Summary of Contents for SW 5070 B

Reviews:

Related manuals for SW 5070 B

Brands by name

Popular brands