background image

SC530 INSTRUCTIONS FOR USE   

ENGLISH 

 

27 

ACCESSORIES/OPTIONS

 

In  addition  to  the  standard  components,  the  machine  can  be  equipped  with  the  following  accessories/options, 
according to the machine specific use:

 

For further information concerning the above-mentioned optional accessories, contact an authorized Retailer.

 

ACCESSORIES/OPTIONS

 

See “Parts List” section

 

1.

 

WET or GEL/AGM  batteries

 

2.

 

Mop and trash kit

 

3.

 

Pads of different materials

 

4.

 

Chemical Mixing System

 

5.

 

Debris collection box

 

 

TROUBLESHOOTING

 

Trouble 

Probable causes 

Remedy 

The  motors  do  not  work;  no 
warning light turns on. 

The battery connector is disconnected. 

Connect the battery connector. 

The batteries are completely discharged. 

Charge the batteries. 

The  machine  does  not  move 
(Only for machine with traction) 

The machine has been turned on by using the ignition 
key and by keeping one of the switches pressed. 

Turn the ignition key to “0”, then try to start 
the  machine  again  without  pressing  the 
switches. 

The  3  battery  charge  indicators 
are flashing simultaneously. 

Brush motor overload. 

Use less aggressive brushes  

Foreign  materials  (tangled  threads,  etc.)  which  may 
prevent the brush from rotating. 

Clean the brush hub. 

The  brushes  do  not  work,  the 
red warning light is on. 

The batteries are discharged. 

Charge the batteries. 

The  recovery  water  vacuuming 
is insufficient. 

The recovery water tank is full. 

Empty the tank. 

The hose is disconnected from the squeegee. 

Connect. 

The  vacuum  grid  is  clogged  or  the  float  is  stuck 
closed. 

Clean the grid or check the float. 

The  squeegee  is  dirty  or  the  squeegee  blades  are 
worn or damaged. 

Clean and check the squeegee. 

The tank cover is not properly closed, or the gasket is 
damaged, or the Bend tube is clogged. 

Close  the  cover  correctly,  or  replace  the 
gasket or clean the Bend tube. 

The recovery water tank is dirty. 

Clean. 

The solution flow to the brushes 
is insufficient. 

The solution/clean water filter is dirty. 

Clean the filter. 

The  squeegee  leaves  marks  on 
the floor. 

There are debris under the squeegee blades. 

Remove the debris. 

The squeegee blades are worn, chipped or torn. 

Replace the blades. 

The squeegee has not been adjusted with the knob. 

Adjust. 

 

 

NOTE

 

Machine with battery charger installed, cannot operate if the charger is not on board. In case of 
battery charger malfunction, contact an authorized Service Center. 
For further information refer to the Service Manual, available at any Service Center. 

 

SCRAPPING

 

Scrap the machine by the qualified waste treatment institution. 

 Before  the  machine  is  scrapped,  please  take  away  and  segregate  below  subassembly  that  relevant  laws  and 

regulations request must be disposed in appropriate way. 

-

 

Battery 

-

 

Brush/Pad-holder 

-

 

Plastic hose and plastic parts 

-

 

Electrical and electronic components (*) 

(*) Please contact our company service center for any destroy of electrical and electronic components. 

Summary of Contents for SC530 53 BD GO































Reviews: