background image

11

US

5  Applications and methods

5.1 General 

information

Efficient high pressure cleaning is achieved by following a few gui-
delines, combined with your own personal experience of specific 
cleaning tasks. Accessories and detergents, when correctly cho-
sen, can increase the efficiency of your pressure washer. Here is 
some basic information about cleaning.

5.1.1 Soaking 

Incrusted or thick layers of dirt can be loosened or softened up by 
a period of soaking. This is for example an ideal method within ag-
riculture – for example, within pig sties. The ideal soaking method 
can be achieved via use of foam or simple alcaline detergent. Let 
the product lie on the dirty surfaces for around 30 minutes before 
pressure washing. The result will be a much quicker high-pressure 
cleaning process.

5.1.2  Detergent and foam 

Foam or detergent should be applied onto dry surfaces so that the 
chemical product is in direct contact with the dirt. Detergents are 
applied from bottom to top, for example on a car bodywork, in order 
to avoid “super clean” areas, where the detergent collects in higher 
concentration and streams downwards. Let the detergent react se-
veral minutes before cleaning off.

5.1.3 Temperature 

Detergents are more effective at higher temperatures. Greases, 
oils and fats can be broken down more easily at higher tempe-
ratures also. Proteins can be cleaned at temperatures of around 
60°C/140°F. Oils, pollution and grease can be cleaned between 
70°/158°F and 90°C/194°F.

5.1.4 Mechanical effect

In order to break down tough layers of dirt, additional mechanical 
effect may be required. Special lances and rotary or wash brushes 
offer this supplementary effect that cuts through dirt. Use a brush 
to cut through e.g. traffic film.

5.1.5  High water flow or high 

pressure 

High pressure is not always the best solution and high pressure 
may damage surfaces. The cleaning effect also depends upon 
water flow. Pressure levels of around 100 bar may be sufficient for 
vehicle cleaning (in association with hot water). Higher flow levels 
give the possibility to rinse and flush away large amounts of dirt 
easily.

Summary of Contents for ALPHA BOOSTER 3



















Reviews: