Nikrans LCD-500GDW Installation Manual Download Page 11 | Manualshive

Page: 11 / 23

background image

Indoor antenna installation

Correct antennas types shall be used according to the site conditions and the requirement.

1. Omni antenna (ceiling Omni or whip antenna) shall be installed in the center and radiate all directions.

2. It is better to use a directional panel antenna or Yaggi antenna when the area shape is long and narrow (corridors, long

row of houses in two sides, tunnels or elevators or rural open space).

Requirements to indoor antenna installation:

• indoor antenna should be 10-15 meter distance from an outdoor antenna

• indoor antenna should be at least 2 meters above the ground

• indoor antenna should be fixed vertically with the ground.

«
...
9
10
11
12
13
...
»

Summary of Contents for LCD-500GDW
























Reviews:

No comments

Related manuals for LCD-500GDW

Brand: Z-Wave Pages: 29

Brand: zBoost Pages: 2

Brand: Black+Decker Pages: 20

Brand: I-View Pages: 4

Brand: Crestron Pages: 2

Brand: J-Tech Digital Pages: 8

Brand: DigitaLinx Pages: 8

Brand: DS Produkte Pages: 44

Brand: Dell Pages: 26

AVENT SCF 860/25

Brand: Philips Pages: 88

Brand: Philips Pages: 96

Brand: Philips Pages: 178

Brand: Philips Pages: 266

Brand: Philips Pages: 363

IDATA HDMI-MX373

Brand: Techly Pages: 16

Brand: Fritel Pages: 12

Brand: Hotpoint Ariston Pages: 84

LICUADORA EHB2425B

Brand: AMERICANA Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands