manualshive.com logo in svg

Nikon SMZ1500, Instructions Manual

Share
Download
Nikon SMZ1500 Instructions Manual Download Page 28

26

3

4

5

6

V

O

L TAGE

Power switch

Brightness adjuster

Changes the illumination brightness when rotated.

Output connector

(Rear view)

(Rear view)

Fuse

Power cord

Input voltage display

Check that the voltage displayed matches the 
voltage used in your area.  If the voltages do 
not match, do not use the power supply and 
contact your Nikon representative.

Always use the fuse 
specified.

Connect the 
lamphouse cable here.

Connect the 
lamphouse cable here.

Power cord

Output 
connector

AC input connector

Brightness adjuster

Power switch

Check that the voltage displayed 
matches the voltage used in your area.  
If the voltages do not match, do not 
use the power supply and contact your 
Nikon representative.

Changes the illumination 
brightness when rotated.

Connect the specified power 
cord here.

Power Supply XN A (only for regions with 100/120 V power)

Power Supply TN-PSE30W A (only for regions with 230 V power)

Input voltage display

3

Power supplies

Use the Power Supply XN A for regions using 100/120 V power, and the
Power Supply TN-PSE30W A for regions using 230 V power.  Insert the
plug of the Halogen illuminator into the output connector located on the
rear of the power supply.

Summary of Contents for SMZ1500






































Reviews:

No comments

Brands by name

Popular brands

Load more brands