manualshive.com logo in svg

Nikon SMZ1500, Instructions Manual

Share
Download
Nikon SMZ1500 Instructions Manual Download Page 21

19

Using Accessories

IV

1

Insert the pillar spacer until it reaches
the bottom of the pillar. (After step  

1

in II “Assembly” on p.10)

2

Mount the zooming body to the P-FMD
focusing mount.

3

Attach the positioning pin to the
positioning pin hole in the zooming
body using a flat-blade screwdriver.

4

Insert the positioning pin on the
zooming body into the positioning
groove of the P-OTR double nosepiece
to fit them.

5

Rotate the objective mounting plate
holding the P-OTR double nosepiece by
hand to set the plate at a position where
the two attaching tool slits at the bottom
of the zooming body connection are
visible.

6

Insert the tool into the attaching tool
slits, and rotate the tool to secure the P-
OTR double nosepiece to the zooming
body.

Objective 
mounting 
plate

Zooming body

Attaching tool slits

Tool

Bottom view

Pillar spacer

Zooming body

Positioning 
pin hole

Positioning pin

Positioning 
groove

Summary of Contents for SMZ1500






































Reviews:

No comments

Brands by name

Popular brands

Load more brands