background image

FCA54001-R.3567.A

- M2 • One Touch Zoom 90s AF -

(8)

 Speed light mode

·Normal mode (1 ~ 5 is changed by the mode button.)

1. Auto

2. Distant view mode (with Flash prohibition)

3. Flash prohibition

4. Forced flash

5. Slow sync (with Forced flash)

·Macro mode

1.  The lens barrel is moved to W end by pressing the macro button.

2.  The photography lens is set to the nearest distance.

3.  The macro button blinks in orange. (4Hz)

4.  The speed light mode is changed to “Forced flash ”.

(9) 

Self-timer

Red eye reduction

 ·Press the self-timer button to set the red eye mode, and the high pressure lamp is turned

  on for 1 second before opening.

 ·The red eye relief mode can be used with each of speed light modes at the same time.  

 In the flash prohibition mode, the high pressure lamp should not be turned on.

Self-timer

 ·Electronic control self-timer: Release occurs after 10 seconds since start.

 ·How to operate: Press the self button on the upper surface of the camera.  After the 

self-timer is displayed in LCD, press the release button.

 ·Operation display: 1Hz for 7 seconds.  For another 3 seconds, it is turned on.

  (The red eye lamp is used.)

 ·How to release: If releasing the self-timer during operation, set the main switch button

  to “OFF ”.

Mode change order

 ·OFF?Red eye mode?Red eye+Self-timer

(10) 

Speed light

 ·GNo: 10 (ISO100·m)

 ·Recycling time: Approx. 7 seconds

Summary of Contents for FCA54001


























































Reviews: