Nikon ECLIPSE MA200 Instructions Manual Download Page 88

Page: 88 / 107

Chapter 4 Assembly

4.14

Intermediate Magnification Unit

Opening for the intermediate magnification unit

1 Remove four bolts to take out the cover on the

attaching part for intermediate magnification unit
with the supplied hexagonal screwdriver.

2 The cables are secured by the cable keeper inside

the opening as the figure shows. Remove the
cable from the cable keeper, then connect the
cable to the connector on the intermediate
magnification unit.

* The cable keeper is attached to MA200 with a

double-side tape. Be sure to remove the keeper
before attaching the intermediate magnification
unit.

3 Insert the intermediate magnification unit to the

opening (with the MAGNIFICATION indications
up) to the limit, then screw the four bolts back into
the microscope securely.

Cable Cable

keeper

Summary of Contents for ECLIPSE MA200












































































































Search results

Summary of Contents for ECLIPSE MA200

Reviews:

Related manuals for ECLIPSE MA200

Brands by name

Popular brands

Nikon ECLIPSE MA200, Instructions Manual

Search results

Summary of Contents for ECLIPSE MA200

Reviews:

Related manuals for ECLIPSE MA200

Brands by name

Popular brands