Niko Easywave 05-331 Manual Download Page 6

 nv 

Niko

 sa    Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: [email protected] — www.niko.be 

PM005-33100R15342

05-331

4. TROUBLESHOOTING

If, after programming, the system does not work, you can perform a number of extra checks.

4.1 New installation

- Check whether the protection between the battery and the contacts in the transmitter has been removed.
- Check whether the battery and the contacts make good permanent contact.
- Reset and (re)program the receiver.
-  Press the programming key. The receiver is now in programming mode. The LED blinks and the load is activated. 

If this is not the case, the receiver is defective.

- Program the transmitters with the receiver and end programming.

4.2. Existing installation

- Check the batteries of the transmitter(s).
- Check the operation of the connected receivers.
- Check for possible interference caused by changes in the system environment (moving of metal cabinets, walls 

or furniture...). Restore the original condition, if possible.

4.3. Transmitter malfunction

Pick up the transmitter and walk towards the receiver.
- The system still works when holding the transmitter in your hand but not when the transmitter is mounted on 

the wall: this may indicate the presence of moist or metal in the wall. In this case, move the transmitter.

- The system still works at reduced distance: the transmitter has been placed outside the transmitter range 

or there is an interference problem. In this case, place the transmitter closer to the receiver or outside the 
interference reach.

- The system does not work even when holding the transmitter close to the receiver: check the programming 

and/or the battery of the transmitter (see above).

4.4. The system automatically switches on and off

- The system automatically switches on: this is only possible if a foreign transmitter was programmed in the receiver 

within the receiver range. Reset the receiver and reprogram the relevant addresses (see ‘3.2. Programming’).

- The system automatically switches off: this situation can be similar to the situation described above or be the 

result of brief current interruptions.

5. TECHNICAL DATA

- transmitter range: 100m in open air; ±30m indoors
-  no wiring between control points and receivers (RF controlled), only one connection between the switch-receiver 

and the device to be operated.

- receiver and transmitter form one integrated whole
- operating temperature: -5 to 45°C
- 1-channel receiver: 1 relay 10A, 230V 50Hz. Only suitable for mono-phase configurations. The contact cannot 

be used for SELV-circuits.

LOAD TABLE

Load type   

Max. load 230V 50Hz*

Resistive: 

10A (40 000x) 

incandescent lamps, halogen 230V~… 

8A (>40 000x) 2 300W

Inductive: low-voltage lighting via ferromagnetic 
transformers (transformer loaded for at least 85%) 

2,6A 

600VA

Non- or series-compensated fluorescent lamps 
with ferromagnetic ballasts 

10A 

2 300VA

Parallel-compensated fluorescent lamps 
with ferromagnetic ballasts 

2,6A 

600W

Electronic control gear 
(HF-fluorescence ballasts, electronic transformers…) 

4A 

920VA

* Max. load with integrated relay: the power can always be extended, also on different phases, with external 

relays

6. WARNINGS REGARDING INSTALLATION

- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This user manual should be presented to the user. It should be included in the electrical installation file, and it 

should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko 
support service.

- During installation, the following should be taken into account (non-exhaustive list):

- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope of 

each specific installation.

- the rules of proper workmanship.

  

This product complies with all of the relevant European guidelines and regulations. If applicable, you can find 

the EC declaration of conformity regarding this product at www.niko.eu.

7. NIKO SUPPORT

In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support 

service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can 

be found at www.niko.eu under the “Help and advice” section.

8. GUARANTEE PROVISIONS

- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase of 

the product by the consumer. If there is no invoice, the date of production applies.

- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating the 

defect.

- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge, 

which shall be decided by Niko.

- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless 

use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance 
instructions or an external cause, such as damage due to moisture or overvoltage.

- The compulsory regulations of the national legislation concerning the sale of consumer goods and the protection 

of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries, chain stores, 
distributors, agents or permanent sales representatives, take priority over the above-mentioned rules and 
regulations.

Hereby, [Niko nv] declares that the radio equipment type 05-331 is in compliance with Directive 1999/5/EC and 

Directive 2014/53/EU. The full text of the EU declaration of conformity is available at www.niko.eu.

Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together 
with producers and importers, you have an important role to play in the advancement of sorting, recycling and 
reusing discarded electrical and electronic appliances. In order to finance the waste collection and processing, 
the government levies a recycling contribution in some cases (included in the purchase price of this product).

9. WIRING DIAGRAM

- For phase (L) and neutral (N) are two connections available to provide 2  x 2,5mm

2

 connectivity. 

- 1 = switch contact 10A 

programming button

230 Vac

250 W

Summary of Contents for Easywave 05-331









Reviews: