background image

www.nkrowing.com.au

1

The Most Relied-Upon

Pocket Weather Instruments 

in the World

Making Work & Play 

Easier & Safer

Thank you for purchasing this SpeedCoach wiring system. PLEASE take a moment to review these instruc-

tions before installing the wiring harness and impeller. Your SpeedCoach system should provide you with 

years of trouble-free service but we are always here to help if a problem arises. To order parts or 

accessories or obtain technical support, please call 02 6553 2473. You may also e-mail  questions to our 

support repre-sentatives at [email protected]  or visit NK online at www.nk.com.au

If you've never done this before, please read through all of these installation instructions 

before permanently installing any part of your SpeedCoach System.

The VHB ("Very High Bond") mounting tape used in this installation requires 24 hours to 

cure to its full bond.  PLEASE avoid getting it wet (in other words, don't take your boat for a 

row) until fully cured.  Failure to do this risks loss of your brand new impeller, or having to 

re-install parts of your system.

Wherever you will be installing VHB mounting tape, make sure to use the provided 

alcohol swabs to clean all oil and dust from the mounting surfaces.  Avoid touching the 

VHB with your fingers as the oil on your skin decreases the bond strength.

IF you ever need to remove installed VHB, use a hair dryer to warm the VHB thoroughly, 

then peel very slowly from one edge to avoid damag

ing the surface.

NK Rowing Electronics Warranty & Service

NK does not believe in "disposable electronics." We know our products don't lead a pampered life, and 

we design them for years of performance in tough conditions.  We guarantee every NK product to be free 

of defects in materials and workmanship for a period of TWO YEARS from your date of  purchase.  We will 

repair or replace any defective product or part when notified within the warranty period, and will return the 

product via domestic ground shipping at no charge. The following issues do not result from a manufacturing 

defect and are not covered under this warranty: damage due to improper use or neglect, including corrosion; 

impact  damage; modifications or attempted repairs by someone other than an authorized NK repair agent; 

normal wear and tear; failed batteries. NK wants you to be an NK customer for life, so we take care of you 

even beyond the terms of the  normal product warranty with our Customer Care Program. Trade-in any NK 

display unit, no matter the age or condition, and receive a generous discount on the replacement product.

Visit www.nk.com.au at any time for detailed product specifications & troubleshooting guides.

SpeedCoach

®

Wiring Installation Instructions

suit SpeedCoach Red, Gold & XL

NIELSEN-KELLERMAN

 

206 Cowans Lane, Oxley Island NSW 2430

 

Phone: 02 

6553 2473

Fax: 02 

6553 2544

 Email: [email protected]

www.nk.com.au

Summary of Contents for SpeedCoach XL2









Reviews: