background image

26

Part # M017879450000  REV. July 1, 2011

ECOTECH EZ

TM

 Variable Speed Motor/Control

recommended maintenance

WARNING

!

 

Before performing any maintenance, 

disconnect the power, allow the motor to come to a 
complete stop and wait five minutes. This will allow the 
control capacitors to safely discharge any residual voltage.

Periodically inspect the installation. Check for dirt 
accumulations, unusual noises or vibration, overheating, 
worn or loose couplings, high motor amps, poor wiring  
or overheated connections, and for loose mounting bolts  
or guards.

Remove dirt accumulation, particularly in and around  
the ventilation openings on the motor by vacuuming.  
Dirt accumulations can cause motor overheating and  
a fire hazard.

Do not use any type of solvents! Some solvents may 
attack the motor insulation, finish or bearing lubricants. 
Solvents are also highly flammable.

This motor uses ball bearings which are permanently 
lubricated. No maintenance is required. 

LImIteD Warranty

Nidec Motor Corporation extends the following LIMITED 
WARRANTY to the purchaser and to its customers 
(collectively referred to as the “Purchaser”) of the enclosed 
motor and components: the motor and components are 
free from defects in materials and workmanship under 
normal use, service and maintenance FOR A PERIOD 
OF 18 MONTHS FROM THE DATE OF ORIGINAL 
PURCHASE FROM NIDEC MOTOR CORPORATION 
OR THE NIDEC MOTOR CORPORATION DEALER/
RETAILER, NOT TO EXCEED 24 MONTHS FROM 
THE DATE OF MANUFACTURE BY NIDEC MOTOR 
CORPORATION. THE FOREGOING WARRANTY 
IS THE ONLY WARRANTY GIVEN AND NO OTHER 
WARRANTY IS PROVIDED, EXPRESS OR IMPLIED, 
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE. Certain 
aspects or disclaimers are not applicable to consumer 
products, i.e., motors and components acquired by 
individuals and used for personal, family or household 
purposes (as distinguished from industrial or other 
purposes). Some states do not allow

 

limitations on how 

long an implied warranty lasts, so the above limitation may 
not apply to you. This warranty gives you specific legal 
rights, and you may have other rights which vary from 
state to state.

Certain repairs or services are the responsibility of 
the Purchaser and the Purchaser is expected to 
pay for them. This warranty does not extend to any 
losses or damages due to misuse, accident, abuse, 
neglect, negligence, unauthorized modification or 
alteration, use beyond rated capacity, or improper 
installation, maintenance, application or use, including, 
without limitation, use in a manner contrary to the 
accompanying instructions or applicable codes. 

If within thirty (30) days after Purchaser’s discovery of 
any warranty defects within the above stated warranty 
period, Purchaser notifies Nidec Motor Corporation or the 
dealer from whom the motor was purchased in writing, 
Nidec Motor Corporation shall, at its option and as 
Purchaser’s sole and exclusive remedy, repair or replace 
or refund the purchase price for, that portion of the motor 
and components found by Nidec Motor Corporation to 
be defective. Failure by Purchaser to give such written 
notice within the applicable time period shall be deemed 
an absolute and unconditional waiver of Purchaser’s 
claim for such defects. Purchaser must write or call the 
dealer from whom the motor was purchased for directions 
regarding the shipment of the motor, with freight pre- or 
call the dealer from whom the motor was purchased for 
directions regarding the shipment of the motor, with freight 
prepaid by the Purchaser, to an authorized service location 
for warranty service. If Purchaser is unable to contact 
the dealer to obtain sufficient instructions regarding the 
handling of the motor, Purchaser should write Nidec 
Motor Corporation at the address on the back cover of 
this manual, giving the model number, the dealer’s name, 
address and number of dealer’s invoice; and describing 
the nature of the alleged defect. Arrangements for warranty 
service will then be made by Nidec Motor Corporation. If 
the motor is damaged in transit, Purchaser should file a 
claim directly with the carrier.

IN NO EVENT, REGARDLESS OF THE FORM OF THE 
CLAIM OR CAUSE OF ACTION (WHETHER BASED 
IN CONTRACT, INFRINGEMENT, NEGLIGENCE, 
STRICT LIABILITY, OTHER TORT OR OTHERWISE), 
SHALL NIDEC MOTOR CORPORATION’S LIABILITY 
TO PURCHASER OR ITS CUSTOMER EXCEED THE 
PRICE PAID BY PURCHASER FOR THE SPECIFIC 
MOTOR OR OTHER GOODS PROVIDED BY NIDEC 
MOTOR CORPORATION GIVING RISE TO THE CAUSE 
OF ACTION. IN NO EVENT SHALL NIDEC MOTOR 
CORPORATION’S LIABILITY TO PURCHASER OR 
ITS CUSTOMER EXTEND TO INCLUDE INCIDENTAL 
CONSEQUENTIAL OR PUNITIVE DAMAGES, WITH 
RESPECT TO CONSUMER PRODUCTS, SOME STATES 
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE 
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY 
TO YOU. 

315612_MNJ26_VAR SPD_nonSRVS.indd   26

7/19/11   8:01 AM

Summary of Contents for ECOTECH EZ





























Reviews: