manualshive.com logo in svg

Nice Linear LNVR1-08P, User Manual

Share
Download
Nice Linear LNVR1-08P User Manual Download Page 25

25

 

Smart Surveillance

Power Up and Power Down

To power up and power down:

On the initial configuration:

1� 

Connect the power cord between the system and power outlet� 

2� 

Turn on the system using the power switch on the back of chassis�

After the initial connection: 

3� 

Use the 

Power Down

 button on the lower right corner of the Settings page� The system should 

start flushing the cached contents in system memory and shut down� You should then flip the 

Power Switch

 button on the back of chassis to completely shut down the system� 

4� 

Press the 

Reset

 button for longer than five (5) seconds can restore system defaults� The 

Reset

 

button is located on the NVR system board (see 

page 13)

�

1� 

No storage system is completely fail-safe� Damage to data might occur due to file system 
corruption, operating system malfunction, virus infection, HDD component failures and so on� 
Therefore, it is highly recommended to regularly back up your data� Data loss or recovery is not 
the responsibility of Nortek Security & Control�

2� 

Always power off the system using the 

Power

 button on the back of chassis� The system is 

powered off when you observe that all LEDs go off� Do not disconnect the power cord while 
the system is still operating� Doing so will result in data inconsistencies� The normal power-off 
procedure allows cached data to be written to disks� 

If system buzzer is sounded, move your mouse cursor to reveal the main screen portal, and then 
click on the 

Stop buzzer

 button� 

Serious system faults, such as a missing volume, can trigger the system buzzer� Verify the cause 
of system fault and turn off the buzzer� 

NOTE:

 WARNING:

Summary of Contents for Linear LNVR1-08P

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands