Nice E Fit L, Instructions And Warnings For Installation And Use

Page: 10 / 52

5.11 - “RDC
. -
tion automatically reduces the motor traction torque, based on the factory setting or the one adjusted by the installer with the following procedure.
– This function is active with the factory setting but is not applicable if the limit switches are programmed with the manual procedure (paragraph 5.6).
Before starting the procedure, bring the awning to the midpoint of its stroke.
01.
n
and
s
keys pressed simultaneously and wait for the motor to perform 2 movements. Upon completion, release the keys.
02.
s
key a few times, depending on the level you want to set for the motor sensitivity:
1 pulse = level 1, standard sensitivity (factory setting)(
*
) 4 pulses = level 4, minimum sensitivity
2 pulses
= level 2, maximum sensitivity
5 pulses
= level 5, function deactivated
3 pulses = level 3, medium sensitivity
. Note – If this does not occur, cancel the proce-
dure. this way, the adjustment is completed without changing the factory setting.
03.
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
01 02
5
sec.
END
03
5
sec.
2
1 /
2
/
3 /
4 /
5 /
10
sec.
0,5
sec.
?
3
x 1 = standard sensitivity(
*
)
x 2 = minimum sensitivity
x 3 = medium sensitivity
x 4 = maximum sensitivity
x 5 = function deactivated
x 1 = standard sensitivity(
*
)
x 2 = maximum sensitivity
x 3
= medium sensitivity
x 4 = minimum sensitivity
x 5 = function deactivated
5.12 - “FRT
This function is useful to eliminate the unsightly depression of the canvas that may form when the awning is open. It is activated by programming position “2” near the
limit switch “1”. . When the function is activated,
when using the automation, the awning lowers to the lower limit switch “1” and then automatically raises to position “2” (the one programmed with the following pro-
cedure), stretching the canvas. The function also acts when a partial opening/closing manoeuvre is commanded. In these cases the awning stops in correspondence
to the height “H” programmed and then rises automatically until the canvas is taut.
• “ “ “. • “
limit switch “1” and limit switch “0”.
Before starting the procedure, bring the awning to the midpoint of its stroke.
01. Press the
t
key and wait for the motor to open the awning until limit switch “1”.
02.
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
03.
s
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04.
s
key pressed again and wait for the motor to perform 4 movements. Upon completion, release the key.
05.
s
key as many times as necessary (the awning will move a few millimetres every time the key is pressed; if the key
“ .
t
key). Note – the position with the canvas taut is position “2”.
06.
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
01
04
02
05
5
sec.
03
5
sec.
0,5
sec.
“ 1 ”
“ 1 ”
2
5
sec.
“ 2 ”
“
1
”
“ 2 ”
2/3cm~
06
END
5
sec.
3
3
4
Note
– When performing the procedure, at any time you can cancel it by keep-
ing the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not
press any key and wait 60 seconds for the motor to perform 6 movements.
Note – When performing the procedure, at any time you can cancel it by keep-
ing the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not
press any key and wait 60 seconds for the motor to perform 6 movements.
9
– English
EN