Nibe S1255-12 Installer Manual Download Page 48 | Manualshive

Page: 48 / 92

Nibe S1255-12 Installer Manual Download Page 48

Menu 5 - Connection

OVERVIEW

5.1 - myUplink

5.2.1 - wifi

5.2 - Network settings

5.2.2 - Ethernet

5.3 - Smart home

1

1 Accessory needed.

MENU 5.1 - MYUPLINK

Here you can manage the installation's connection to
myUplink (

) and see the number of users

connected to the installation via the internet.

A connected user has a user account in myUplink ,
which has been given permission to control and/or
monitor your installation.

Request new connection string

To connect a user account on myUplink to your installa-
tion, you must request a unique connection code.

1.

Select "Request new connection string"

2.

The installation now communicates with myUplink
to create a connection code.

3.

When a connection string has been produced, it is
shown in this menu and is valid for 60 minutes.

Disconnect all users

To disconnect the users who are connected to the in-
stallation via myUplink, select "Disconnect all users".

NOTE

After disconnecting all users none of them can
monitor or control your installation via myUplink
without requesting a new connection string.

MENU 5.2 - NETWORK SETTINGS

Here, you choose whether your system connects to the
Internet via wifi (menu 5.2.1) or via a network cable
(Ethernet) (menu 5.2.2). From each menu, you can make
settings for TCP/IP.

TCP/IP settings

You can set TCP/IP settings for your installation here.

Automatic setting (DHCP)

Activate "Automatic". The installation now receives the
TCP/IP settings using DHCP.

Manual setting

Select "IP address" and enter correct address using the
keyboard.

Repeat the procedure for "Network mask", "Gateway"
and "DNS".

Caution

The installation cannot connect to the internet
without the correct TCP/IP settings. If unsure
about applicable settings use the automatic
mode or contact your network administrator
(or similar) for further information.

TIP

All settings made since opening the menu can
be reset by selecting "Reset".

MENU 5.3 - SMART HOME (ACCESSORY
REQUIRED)

If you have a Smart home system that can communicate
with myUplink, you activate these functions in this
menu.

Caution

The Smart Home function requires myUplink
in order to work.

NIBE S1255

Chapter 9 | Control - Menus

48

«
...
46
47
48
49
50
...
»

Summary of Contents for S1255-12





























































































Reviews:

No comments