Nibe ERS 10-500 Installer Manual Download Page 9

Page: 9 / 28

Pipe connections

Ventilation connection, exhaust air

XL31

Ventilation connection, extract air

XL32

Ventilation connection, supply air

XL33

Ventilation connection, outdoor air

XL34

Condensation water drain

XL40

Sensors etc.

Temperature sensor, exhaust air

BT20

Temperature sensor, extract air

BT21

Temperature sensor, supply air

BT22

Temperature sensor, outdoor air

BT23

Electrical components

Accessory card

AA5

Heat exchanger

EP26

Cable gland

UB1

Cord with connection plug

Control cable

Ventilation

Heat exchanger

EP26

Fan, exhaust air

GQ2

Fan, supply air

GQ3

Air filter, exhaust air (Coarse filter class G4)

HQ10

Air filter, supply air (Fine filter class F7)

HQ11

Bypass damper

QN37

Miscellaneous

Type plate

PF1

Condensation water trough

WM5

Designations in component locations according to
standard IEC 81346-1 and 81346-2.

Chapter 3 |

The ventilation heat exchanger design

NIBE™ ERS 10-500

Summary of Contents for ERS 10-500





























Search results

Summary of Contents for ERS 10-500

Reviews:

Related manuals for ERS 10-500

Brands by name

Popular brands

Nibe ERS 10-500, Installer Manual

Search results

Summary of Contents for ERS 10-500

Reviews:

Related manuals for ERS 10-500

Brands by name

Popular brands