Nexus 21 L-50s Installation Instructions Manual Download Page 3

 

Parts List, continued 

 
 
 
 
 
 
 
 
 

Cables

   

 

Motor Cable 2.5m (1)

 

 Black cable with white, six-pin plugs. Use this cable to connect the Lift Column to the Control Box. 

 

Power Cable

 

 Connects Control Box to power outlet. Three feet long. 

 

RF Cable (only present if you ordered the RF version of the Lift System) 

 Use to connect the RF Receiver to the Control 

Box. Ends have RJ-45 connectors. One-foot long. 

 

Interface Cable 

 

Six inch long black cable with one white six pin plug, one female mini jack port, and one female white six 

pin port. Used for Swivel Cutoff Feature. 

 

Hardware 

1.

 

Twelve (12) -- 6 x 12mm BHMS (Button Head Machine Screw) 

2.

 

Four (4) -- 6 x 16 BHMS (Button Head Machine Screw) 

3.

 

Four (4) -- 

3/8” –

 

16 x ½” BHMS (Button Head Machine Screw)

 

4.

 

Four (4) 

 6 x 12mm FHMS (Flat Head Machine Screw) 

5.

 

Four (4) 

 6 x 16mm FHMS (Flat Head Machine Screw) 

6.

 

Four (4) -- 

#8 x ¾” FHWS (Flat Head Wood Screw)

 

7.

 

Two (2) -- #10 x 1-

¾” FHWS (Flat Head Wood Screw)

 

8.

 

Eighteen (18) -- 

#10 x ¾” THWS (Truss Head Wood Screw)

 

9.

 

One (1) 

 Small Hex Key (4mm) 

10.

 

One (1) 

 

Large Hex Key (7/32”)

 

11.

 

Four (4) 

 Universal Lid Catches 

12.

 

One (1) 

 Large Assorted TV Hardware Pack 

13.

 

Two (2) 

 Threaded Tapered Pins 

14.

 

Four (4) 

 Wire Clips 

15.

 

Four (4) 

 Snakeskin Ties 

16.

 

Four (4) 

 Plastic Wire Ties 

 

Additional Hardware included in “Swivel Pak”

 

17.  

Four (4) 

 6mm x 10mm Button Head Machine Screw 

18.

  Four (4) 

 6mm x 16mm Button Head Machine Screw 

19.  

One (1) 

 

1.25” Flat Head Wood Screw 

 

 

Wire Management 

The Lift  System has no exposed gears or moving parts  that can damage your 
wires,  so  wire  management  is  simple.  We  have  included  a  four-foot  long 

“SNAKESKIN” sleeve, which is a state

-of-the-art wire bundling and protection 

system (the sleeve can be cut shorter if you wish). The System also includes 4 
Velcro  end  ties  and  4  plastic  ties.    Use  the  Velcro  ties  at  the  ends  of  the 
SNAKESKIN, to close the ends of the sleeve and to keep the wires together inside 
it. Use the plastic ties to fasten the cable bundle in a fixed position, so it moves 
up and down with the lift.  

 

 
 
 

Control Box 

Swivel Mechanism 

Assorted TV Mounting Screws 

Summary of Contents for L-50s

























Reviews: