manualshive.com logo in svg

Next NI400, User Manual, Page: 53 / 59

Share
Download
Next NI400 User Manual Download Page 53

0104

 www.ruggedaq.com

DATALOGGER

NI400

NI400

0105

 www.ruggedaq.com

DATALOGGER

NI400

NI400

ANOMALIES AND ALARM WARNINGS

Error Codes

When the NI400 is in error status, it shows the letter “E” and error codes one after the 

other. Following, there are NI400 error codes.

ERROR CODE

DESCRIPTION

E0

General Communication or FTP/MAIL connection Error. 

It refers to log events on web server

E1

USB Drive not found.

E2

Error in file copy.

E3

NI400 is already in run state.

E4

It is impossible to start the NI400.

E5

NI400 is already in configuration state.

E6

Iti s impossible to stop the NI400.

The system shows general error codes because it has a simple display and so it would be 

difficult to encode each case.  The system will log the event/error and it will be visible and 

downloadable from the web. 

9

9

Icons and power supply alarm thresholds

NI400 with external power supply

Icon showed: plug

Display: L

High alarm threshold: 14V

Low alarm threshold: 10.5V

NI400 with internal battery pack

Icons showed: cell (battery)

Full battery: voltage≥ 9.6V

Medium battery: 8.76V < voltage < 9.6V

Low battery: Voltage ≤ 8.76V

Display: 

3 lines: Voltage ≥ 9.6V

2 lines: 8.76V < voltage < 9.6V

1 line: voltage ≤ 8.76V

High alarm threshold: not present

Low alarm threshold: 8.76V

Summary of Contents for NI400




























































Reviews:

No comments