Next MILANO 895465 Assembly Instructions Manual Download Page 1

Tools Needed

Helpline

If you have any problems with this product or require 
any replacement fittings please contact Customer 
Services Tel: 0333 777 8999

ASSEMBLY INSTRUCTIONS

Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be 
faulty. Should you need to return the unassembled product, please repack in the original packaging.

IMPORTANT

• Carefully check that you have all parts before beginning assembly.

• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. 

IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY

895465  MILANO  BLACK GLOSS

TALL SHELF

• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.

CARE INSTRUCTIONS

• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.

• Never drag pieces of furniture across the floor as this will cause damage to the joints.

• Made from PB,MDF,hollow board & Honeycomb board with a pvc foil finish.

• Made in China.

• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or 
warping.

PRODUCT INFORMATION

• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or 
damage.

• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft cloths 
(including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try your cloth in 
an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for cleaning is included 
within the hardware pack

• Carefully check that you have all parts before beginning assembly.

• Do not use furniture polish.

• Do not put hot dishes directly on the surfaces of the item.

• Keep fittings out of children's reach and keep children well away from the construction area.

•Gloss finishes are prone to light surface scratch and it is therefore very important that 
you  care for this item correctly.

• Do not rub or scrub the surface when cleaning.

• We recommend that the packaging is used to protect the surfaces during assembly.

• A minimum of two persons is required to assemble this product.

Page 1 of 10

Summary of Contents for MILANO 895465











Reviews: