background image

Tools Needed

Helpline

If you have any problems with this product or require

any replacement fittings please contact Customer

Services Tel: 0844 844 8999

  damage.

• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.

• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.

• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.

• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or   

• Ensure the mats and coasters used do not have an abrasive surface underneath.

• Made from particleboard,MDF with a wood effect finish.
• Made in Indonesia.

CARE INSTRUCTIONS

• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons are required to assemble this product.

ASSEMBLY INSTRUCTIONS.

IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.

Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be 
faulty. 

Should you need to return the unassembled product, please repack in the original packaging.

IMPORTANT

• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. 

PRODUCT INFORMATION

802062              BARLOW COFFEE TRUNK

7

5

6

6

3R

3R

3L

5

6

6

3L

3R

7

1 of 9

Summary of Contents for BARLOW 802062










Reviews: