NexPump Ai Single User Manual Download Page 4

NEXPUMP PRECAUTIONS:

NexPump SYSTEM Unit Location

Locate the NexPump System Unit as far away
from the battery as the DC cables permit. 

Do not operate the NexPump System Unit in an area with 
restricted ventilation.

Do not set a battery on top of the NexPump
System Unit.

Do Not allow the NexPump System Unit to sit on top of 
the battery.

Do not block NexPump System Unit ventilation in any 
way.  Allow at least 6 inches of free space from the fan 
exhausts on the right side of the NexPump Unit.

Do not install the NexPump System Unit where 
temperatures will be below freezing (32 degrees 
Fahrenheit).

Do not install the NexPump System Unit where it will be 
exposed to outside elements.

DC CONNECTION PRECAUTIONS

The NexPump Unit requires a connected marine type 
deep-cycle battery for proper operation. You must assure 
the battery is connected while the NexPump Unit is 
operating.

When attaching the battery cables to the battery posts, 
secure them to insure a good connection.

The BLACK wire from the NexPump System Unit 
connects to the NEGATIVE (-) post of the battery.
The RED wire from the NexPump System Unit
connects to the POSITIVE (+) post of the battery.

The ‘REVERSE POLARITY LED’ will illuminate if
the battery connections are reversed.

AC POWER REQUIREMENTS

The NexPump System Unit must be operated from 120 
volt household current from the AC outlet. 

GROUNDING AND AC CORD INSTRUCTIONS

The NexPump System Unit should be plugged into
an outlet that is properly installed and grounded in 
accordance with all local codes and ordinances. 

DANGER

Never alter the AC cord or plug provided – if it will not fit 
the outlet, have a proper outlet installed by a qualified 
electrician. Improper connection can result in a risk of an 
electric shock.. An adapter should not be used with this 
NexPump System Unit. 

Important Safe Guards:

Never allow other items that discharge into the sump pit to 
be unsecured. Unsecured items such as garden hoses, 
laundry hoses and other medium used to discharge water 
may interfere with the NexPump pumps or sensors. Be 
sure to secure all items that may be used to discharge water 
into the sump pit and verify that secured items will not 
interfere will any NexPump operations.

4

Summary of Contents for Ai Single























Reviews: