background image

5

FORM NO. L-20063-AG-1216

INTRODUCTION

BEFORE YOU BEGIN

Nexen has introduced a new actuator for BD Caliper Brake spring-engaged models. The old Three-Port Actuator is 
obsolete.  

The new two actuator is geometrically different and the manual disengagement mechanism operates differently. The new 
actuator for the 60 psi release unit is unique in look from the new two port actuator. 

The redesigned two-port model has a rubber hose on the exterior of the product used for balancing internal air pressure. 
The service and spring ports for this model have been redesigned and simplified.

The mounting procedures on both actuators are identical.

Review the summary of actuator differences below before beginning any installation or maintenance procedures. 

NOTE

The installation and maintenance procedures for each model are located next to each other in this manual. Be 

sure to follow the appropriate instructions for each model.

S

ummary

 

of

 D

ifferenceS

 

in

 BD a

ctuatorS

Read this manual carefully, making full use of its explanations and instructions.  The "Know How" of safe, continuous, trouble-free 

operation depends on the degree of your understanding of the system and your willingness to keep all components in proper 

operating condition.  Pay particular attention to all NOTES, CAUTIONS, and WARNINGS to avoid the risk of personal injury or 

property damage.  It is important to understand that these NOTES, CAUTIONS, and WARNINGS are not exhaustive.  Nexen 

cannot possibly know or evaluate all conceivable methods in which service may be performed, or of the possible hazardous 

consequences of each method.

Accordingly, anyone who uses a procedure that is not recommended by Nexen must first satisfy themselves that neither their 

safety or the safety of the product will be jeopardized by the service method selected.

Obsolete 3 Port Actuator

2 Port Actuator

60 PSI Release Actuator

Overall Length

214 mm [8.41 in]

169 mm [6.67 in]

165 mm [6.5 in

Diameter

160 mm [6.31 in]

163 mm [6.44 in]

184.2 mm [7.25 in]

Clamping Force

Refer to catalog data

5% greater

Refer to catalog

Hold-Off Pressure

4.96 bar [72 psi]

5.10 bar [74 psi]

4.1 bar [60 psi]

Power Spring

Telescoping

Non-coil clash

Multiple coil

Ports

One spring release

and two plugged ports

One spring release

and one plugged port

One spring release

and one vent port

CAUTION

The user(s) of this equipment must comply with 

operating procedures and training of operating 

personnel as stated in the Occupational Safety 

and Health Act (OSHA) Standard (29 CFR 1910) 

Section 1910.219-K.

Summary of Contents for 933500






















Reviews: