NexDome 2.2m Dome Rotation Kit Installation And Operation Manual Download Page 8 | Manualshive

Page: 8 / 12

background image

NEXDOME OBSERVATORIES NEXDOME.COM

Page 8

Figure 7: Connect to dome.

Next, click the “Connect” button and a new control window will open (Fig 8). Press the home
button and the dome should start to rotate. It will stop when the magnetic switch and magnet
align. Note the real life azimuth position of the dome slit (not what’s on the screen) and enter
this value in “Home azimuth” field.

«
...
6
7
8
9
10
...
»

Summary of Contents for 2.2m Dome Rotation Kit













Reviews:

No comments

Related manuals for 2.2m Dome Rotation Kit

Brand: IAI Pages: 5

Brand: Zeta Pages: 44

Brand: Dahua Pages: 137

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: V2 Pages: 48

Brand: YASKAWA Pages: 12

Brand: D+H Pages: 36

Brand: netvox Pages: 12

Brand: Oriental motor Pages: 52

Brand: Opt Pages: 40

Brand: REMKO Pages: 20

Brand: Evco Pages: 78

Brand: Yale Pages: 2

Brand: Hide-A-Hose Pages: 13

Brand: Sorel Pages: 20

Brand: VADDIO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands