manualshive.com logo in svg

Nexans Euromold 200LR, Installation Instructions Manual

Share
Download
Nexans Euromold 200LR Installation Instructions Manual Download Page 4

1

  Fold one strip of mastic twice (4 layers) and place it under the solder block on the braid. Then wrap the second 

 

strip of mastic over the solder block of the braid and around the outer sheath.

2 

Fixate the flexible braid using adhesive tape.

3

  Apply two layers of semi-conductive tape, overlapping the water sealing mastic by 

5

 mm and overlapping the 

 

earthing device by 

5

 mm (50% stretch, 50% overlap).

semi-con-

ductive tape

water sealing

mastic

water sealing

mastic

adhesive tape

solder block

on the braid

5

two layers of semi-conduc-

tive tape

5

WATERSEALING

earthing

device

1

  As a protection, wrap a few turns of adhesive tape around the conductor end.

2

  Lubricate* the indicated area : cable surface and inner surface of the reducer.

3

  Slide the reducer down the cable.

4

  Remove the protective adhesive tape from the conductor.

INSTALLATION OF THE CABLE REDUCER

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

lubricate

core insulation

cable reducer

outer

cable

sheath

water sealing

mastic

solder block

on the braid

IS97082-ENG - 200LR/G

-MT345 - Revision 0

Page 4/9

Summary of Contents for Euromold 200LR










Reviews:

No comments

Brands by name

Popular brands

Load more brands